-
can转以太网网关，采用NUTOS NUTNET
can转以太网网关，采用NUTOS NUTNET-can switch to Ethernet gateway, using NUTOS NUTNET
- 2022-06-28 02:25:07下载
- 积分：1
-
缺水传感器V1.0，绝对原创，传感器好
缺水传感器V1.0，绝对原创，传感器好-Water sensor V1.0, an absolute original, a good sensor
- 2022-03-07 18:57:53下载
- 积分：1
-
procedure for the development of SCM LCD LCD demo program using compiled languag...
此程序为单片机开发中的lcd 液晶演示 程序，采用汇编语言编写，经过调试运行 无误。-procedure for the development of SCM LCD LCD demo program using compiled languages, through commissioning and truthful.
- 2023-02-08 04:20:03下载
- 积分：1
-
单片机与计算机的互连，C51的Keil工程文件和PC机的C++文件。
单片机与计算机的互连，C51的Keil工程文件和PC机的C++文件。-Single-chip interconnection with the computer, C51 of the Keil project file and PC-C++ files.
- 2022-07-23 20:45:27下载
- 积分：1
-
MB90092 paper, Fujitsu MB90092 driver
MB90092文件，富士通MB90092的驱动程序 -MB90092 paper, Fujitsu MB90092 driver
- 2022-07-08 02:03:12下载
- 积分：1
-
8051上的CRC8校验 A CCITT
8051上的CRC8校验 A CCITT-8 CRC calculator. The source contains both the calculated (smaller but slower) version, and the table driven (faster but larger) version.-8051 CRC8 check on the CCITT A-8 CRC calculator. Th e source contains both the calculated (smaller but slower) version, and the table driven (faster but larger) versio n.
- 2022-03-09 13:40:44下载
- 积分：1
-
一个经典的电子钟程序，采用汇编语言编写，时钟芯片采用DS12C887，具有遥控器修改时间等功能...
一个经典的电子钟程序，采用汇编语言编写，时钟芯片采用DS12C887，具有遥控器修改时间等功能-A classic bell electronic procedure for the preparation of assembly language, the clock chip DS12C887, with remote control features such as modified
- 2022-11-06 21:10:03下载
- 积分：1
-
89c52编写智能化开关电源设计，带A/D,D/A识别全数字开关电源程序。...
89c52编写智能化开关电源设计，带A/D,D/A识别全数字开关电源程序。-89c52 prepare intelligent switching power supply design, with A/D, D/A to identify an all-digital switching power supply procedures.
- 2022-02-03 02:00:42下载
- 积分：1
-
IC Card operating software : AT88SCl604 chip mode of operation there are five. T...
IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta
- 2022-05-28 08:23:00下载
- 积分：1
-
自己写的测试串口的小工具，巨好用！他可以完成十六进制和字符同时显示...
自己写的测试串口的小工具，巨好用！他可以完成十六进制和字符同时显示-himself wrote the serial testing of small tools, giant handy! He can be completed hexadecimal characters and shows
- 2022-01-26 20:00:06下载
- 积分：1
