登录
首页 » 嵌入式系统 » 基于S3C2440 对 K9F1208 Nand Flash 的读写,取自uboot,对其进行了修改

基于S3C2440 对 K9F1208 Nand Flash 的读写,取自uboot,对其进行了修改

于 2023-02-17 发布 文件大小:5.53 kB
0 98
下载积分: 2 下载次数: 1

代码说明:

基于S3C2440 对 K9F1208 Nand Flash 的读写,取自uboot,对其进行了修改-S3C2440 based on K9F1208 Nand Flash reading and writing, from uboot, its modified

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • WSN仿真一例假定节点0(node[0])周期性广播消息其它节点接收到消息并转发出去...
    WSN仿真一例假定节点0(node[0])周期性广播消息其它节点接收到消息并转发出去-Sensor Simulation case assumptions 0 nodes (node [0]) cyclical broadcasting news other nodes to cancel the reception Interest and transmitted out
    2023-02-02 18:25:04下载
    积分:1
  • ActiveTcl is ActiveState s quality
    ActiveTcl is ActiveState s quality-assured distribution of Tcl, available for AIX, HP-UX, Linux, Mac OS X, Solaris, and Windows
    2022-04-30 06:03:57下载
    积分:1
  • 终端IAR LPC1114
    终端程序通过UART终端建设,使自己的菜单程序的。设备是LPC1114和环境是IAR
    2022-03-26 02:45:15下载
    积分:1
  • 我自己写的ds1820b温度测量程序,可以通过串口工具软件显示温度...
    我自己写的ds1820b温度测量程序,可以通过串口工具软件显示温度-I wrote it myself ds1820b temperature measurement procedures, through serial software tools show that the temperature
    2022-12-06 00:30:03下载
    积分:1
  • STM32无刷直流电机驱动
    资源描述STM32采用TIM1的PWM输出,控制直流无刷电机 上传一个基本初级版的程序 PA8 PA9 PA10 PB13 PB14 PB15是PWM输出口 PC5接个电位器调节速度 PB12电源指示灯 PB5正转指示 PB2反转指示 PB0按键开机 PB1按键正反转 宏定义DEBUG可以软件仿真(DEBUG用来开启相关变量,以及变换霍尔相序)
    2023-08-18 02:45:04下载
    积分:1
  • EAC
    EAC-STN-V2.00接线图.pdf-EAC-STN-V2.00 wiring diagram. Pdf
    2023-02-28 02:30:02下载
    积分:1
  • 南描述了如何在AT90S1200上实现轮询(polled)软件UART
    南描述了如何在AT90S1200上实现轮询(polled)软件UART-South describes how to achieve the AT90S1200 Polling (polled) software UART
    2022-07-16 09:14:03下载
    积分:1
  • 利用集成智能温度传感器测量温度,采用光纤传输温度信号。由单片机(HT46R24)控制温度传感器(DS18B20)的温度采集。当有采集温度的指令的时候,...
    本系统利用集成智能温度传感器测量温度,采用光纤传输温度信号。系统由单片机(HT46R24)控制温度传感器(DS18B20)的温度采集。当有采集温度的指令的时候,才启动温度传感器并采回其数据,在没有进行温度采集的时候,将通过抬高温度传感器的地,关断其工作电源,如此可以降低系统的功耗。系统将每一次采集回来的数据与前一次的数据比较,若温度变化超限或温升超标,立即发送上述温度值;否则,累加到采集了一定的次数,再向主机发送最新温度值。-The system uses an integrated smart temperature sensors measure temperature, using optical fiber transmission temperature signal. System consists of microcontroller (HT46R24) controlling the temperature sensor (DS18B20) the temperature of collection. When a collection of instructions, when the temperature before start-up temperature sensors and taken back to its data, collected in the absence of the temperature when the temperature sensor will raise, the turn-off the power of their work, so you can reduce system power consumption. The system will come back every time collecting data and previous data comparison, if the temperature changes or temperature exceeding overrun immediately send the temperature value otherwise accumulate to collect a certain number of times, again
    2022-02-22 01:47:25下载
    积分:1
  • kangyl _ PCI _ _ 30 _设计指南
    kangyl_Pci_design_guide_30
    2022-02-01 07:51:41下载
    积分:1
  • 学习AVR C语言编程的门与提高的经典书籍,喜欢的朋友可以
    学习AVR C语言编程的入门与提高的经典书籍,喜欢的朋友可以-AVR C programming language learning portal with the improvement of the classic books, like our friends can see
    2022-01-25 21:14:46下载
    积分:1
  • 696518资源总数
  • 105540会员总数
  • 37今日下载