登录
首页 » 嵌入式系统 » This document is an electronic programming keil table design, the realization of...

This document is an electronic programming keil table design, the realization of...

于 2023-03-09 发布 文件大小:18.83 kB
0 100
下载积分: 2 下载次数: 1

代码说明:

本文件是用keil编程的电子表的设计,实现时,分,秒的加减,和定时功能-This document is an electronic programming keil table design, the realization of hours, minutes and seconds of the addition and subtraction, and the timing

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • GPS,怎样接收坐标数据,以及对数据的处理
    GPS系统,怎样接收坐标数据,以及对数据的处理-GPS systems, how to receive coordinate data, as well as data processing
    2022-01-26 04:59:25下载
    积分:1
  • The use of Atmel8L through I2C channels of communication with the IRIC check the...
    使用Atmel8L通过I2C通道与IRIC通信,检查IRIC是否正常工作
    2022-06-26 09:21:57下载
    积分:1
  • MCU控制TRF3765的源代码
    使用单片机控制4路TRF3765的源代码,单片机是STC15F2K60S。控制锁相环产生不同频率的信号
    2022-11-26 16:45:08下载
    积分:1
  • stepper motor control procedures
    步进马达控制程序-stepper motor control procedures
    2023-01-27 18:50:03下载
    积分:1
  • SD_FAT
    STM32-SDCard-SDIO-FATFS-V2 stm32 SD 读卡器,非常实用 
    2023-04-20 19:50:03下载
    积分:1
  • qpboc L2源码
    可以通过QPBOC检测 里面有emv内核源码 和qpboc的一些文档的数据结构定义和代码的介绍 里面有大量的注释 很好的代码。
    2022-03-09 17:12:39下载
    积分:1
  • Wince from a large number of source code stripped out of the fat file system sou...
    从大量的wince源代码中剥离出的fat文件系统源代码.移植性非常高. 里面带有source i.rar-Wince from a large number of source code stripped out of the fat file system source code. Portability is very high. Inside with a source i.rar
    2022-01-22 12:01:01下载
    积分:1
  • 1、ARM7芯片LPC2138驱动ym320240的点阵液晶. 2、320240的液晶驱动.
    1、ARM7芯片LPC2138驱动ym320240的点阵液晶. 2、320240的液晶驱动. -1, ARM7 chip LPC2138 dot matrix LCD driver ym320240 the .2,320240 the LCD driver.
    2022-05-16 20:25:29下载
    积分:1
  • PIC16F877A 24C02读写
    资源描述 /*************************************************************************** * 文件名:24c02 * 功  能:利用IIC总线对eeprom 24c02,进行读写 * 作  者:TXMCU * 日  期: * 备  注: //软件思路:当按键KEY0按下时,把6个连续的数据写入到6个连续的单元内, //写完成后数码管显示单个0,做为完成标志位,当按键KEY1按下后, //读取EEPROM连续六个单元,读取结果送6位数码管显示 //           //开发板连接方法:将JP10 JP11 JP12 JP13这4个跳线帽分别接到24C02位置 // 把JP8的的跳线帽跳到DPY位置上,JP14选择在IO口位置上 ****************************************************************************/ #include __CONFIG(0x1832); //芯片配置字,看门狗关,上电延时开,掉电检测关,低压编程关,加密,4M晶体HS振荡 #define address  0xa #define nop() asm("asm") //定义待写入的数据 const char ee_data_write[] = {0, 4, 2, 3, 3, 1}; //定义读取数据存放的缓冲区 unsigned char ee_date[6]; //定义0-9的显示代码
    2022-03-18 07:32:17下载
    积分:1
  • C语言开发的数字钟程序,希望对大家有用!真是第二个文件!...
    C语言开发的数字钟程序,希望对大家有用!真是第二个文件!-development of the C language digital clock procedures in the hope that it may be useful right! The second document is!
    2022-03-19 11:58:08下载
    积分:1
  • 696518资源总数
  • 105873会员总数
  • 12今日下载