登录
首页 » SCM » 用于单片机的开发 用modbus协议 实现上位机与下位机的通讯

用于单片机的开发 用modbus协议 实现上位机与下位机的通讯

于 2023-04-22 发布 文件大小:36.75 kB
0 26
下载积分: 2 下载次数: 1

代码说明:

用于单片机的开发 用modbus协议 实现上位机与下位机的通讯-design for mcu,protocl is modbus,for double mcu commiunication

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 电子密码锁源码,VB》NET,加硬件键盘可工作
    电子密码锁源码,VB》NET,加硬件键盘可工作-Electronic Code Lock Source, VB " NET, plus the hardware keyboard to work
    2022-03-17 10:28:54下载
    积分:1
  • KEIL51的一元二次方程的程序
    KEIL51的一元二次方程的程序-KEIL51 a square procedure
    2023-05-10 23:15:03下载
    积分:1
  • 51系列单片机实验课程:按键显示程序 (在数字键上按数字,在液晶显示器上显示)...
    51系列单片机实验课程:按键显示程序 (在数字键上按数字,在液晶显示器上显示)-51 Series single-chip experimental curriculum: key display program (in the figure by the number keys on the LCD display)
    2022-03-15 13:53:53下载
    积分:1
  • 一种采用CYPRESS的PSOC混合信号控制其系列的智能型充电器设计方案,可支持多种电池理性,根据电池充电曲线进行调整,开发IDE为CYPRESS的PSOC D...
    一种采用CYPRESS的PSOC混合信号控制其系列的智能型充电器设计方案,可支持多种电池理性,根据电池充电曲线进行调整,开发IDE为CYPRESS的PSOC Designer,硬件为PSOC。-use of a PSOC mixed-signal control of its series of smart charger design that can support multiple battery rational, battery charging curve adjustment, IDE for the development of the PSOC Designer CYPRESS, hardware PSOC.
    2022-03-25 04:14:02下载
    积分:1
  • 学习用,使用前,认真阅读,按实际情况更改IO口!
    学习用,使用前,认真阅读,按实际情况更改IO口!-to study, use, read carefully, according to the actual situation changes IO mouth!
    2023-01-21 13:10:04下载
    积分:1
  • 一个良好的键盘扫描程序的执行效率。用Proteus仿真图…
    一个执行效率不错的键盘扫描程序。附有Proteus仿真,按键的键值通过LED显示-A good efficiency in the implementation of the keyboard scanner. With Proteus simulation, the key button LED display through
    2023-03-07 00:05:04下载
    积分:1
  • 8279与单片机接口 8279与单片机接口
    8279与单片机接口 8279与单片机接口
    2022-06-16 03:09:16下载
    积分:1
  • ATMEL单片机可用的文件系统源代码,支持FAT16/FAT32格式。
    ATMEL单片机可用的文件系统源代码,支持FAT16/FAT32格式。-ATMEL SCM available file system source code, support FAT16/FAT32 format.
    2022-06-27 07:47:01下载
    积分:1
  • MCS
    MCS-51单片机有5个中断源,其中两个是由-INT0、-INT1引脚输入的外部中断源;另外三个是内部中断源即由T0、T1的溢出引起中断和串行口发送完一个字节或接收到一个字节数据引起中断。触发外部中断有两种方式,即下降沿引起中断或低电平引起中断。当编程TCON中的ITi(i=0、1)为1时,则引起触发的方式为边沿触发方式,反之(ITi=0)为低电平触发方式。每个中断源的中断请求能否得到响应要受两级“开关”的控制,即一个总“开关”-MCS-51 single-chip has five interrupt sources, two of which are by-INT0,-INT1 pin input external interrupt source the other three internal interrupt sources from the T0, T1 overflow caused by the disruption and serial port sending or receiving end of a byte to a byte of data caused by interruption. Triggered external interrupt has two modes, namely, falling edge or low-level disruption caused disruption caused. When programming TCON in ITi (i = 0,1) for the 1:00 has been the subject of a way to trigger the way to the edge of the trigger, on the contrary (ITi = 0) for low-level trigger mode. Each interrupt source interrupt request can be subject to levels in response to
    2023-07-06 00:00:03下载
    积分:1
  • 单片机Com端口仿真,有程序及仿真原理图
    单片机Com端口仿真,有程序及仿真原理图-Com-port single-chip simulation, there are procedures and simulation schematic
    2022-02-02 21:13:22下载
    积分:1
  • 696524资源总数
  • 103986会员总数
  • 80今日下载