-
凌阳单片机的串口通信程序，在SPCE061A芯片上调试通过
凌阳单片机的串口通信程序，在SPCE061A芯片上调试通过-Sunplus Single-chip serial communication procedures, in SPCE061A chip debugging through
- 2022-01-23 11:03:40下载
- 积分：1
-
这是在KEIL环境下写的CAN源码，具有CANOPEN协议，学习参考的好东西哟！...
这是在KEIL环境下写的CAN源码，具有CANOPEN协议，学习参考的好东西哟！-This is in KEIL environment CAN write source code, with CANOpen agreement, a reference to learn good things yo!
- 2022-01-26 02:36:06下载
- 积分：1
-
i2c通讯控制程序,很快的实现对24c02的通讯功能
i2c通讯控制程序,很快的实现对24c02的通讯功能-i2c communication control procedures, quickly realizing the communication function 24C02
- 2023-05-01 17:45:02下载
- 积分：1
-
程序由C语言编写，时序完全达到要求，含有proteus仿真图。硬件上已经测试通过！...
程序由C语言编写，时序完全达到要求，含有proteus仿真图。硬件上已经测试通过！-Procedures by the C language, timing fully meet the requirement, contained Proteus simulation of Fig. Hardware has been tested!
- 2022-04-15 10:03:42下载
- 积分：1
-
pic microcontroller c language guides, microship Company engineers to write tech...
pic单片机c语言教程，microship公司工程师写的技术文章，对使用pic的c编程很有帮助，本文章是中文版。-pic microcontroller c language guides, microship Company engineers to write technical articles, the use of the c pic programming venture, the article is the Chinese version.
- 2022-07-14 15:01:46下载
- 积分：1
-
ST9720控制器的12864液晶程序，兼容12232，本程序使用…
ST9720控制器的12864液晶程序，同时兼容12232，本程序使用串行接法。只需三个管脚。-ST9720 LCD controller 12864 program is compatible with 12232, this program uses a serial access method. Just three pins.
- 2022-08-20 03:16:22下载
- 积分：1
-
详细介绍了单片机的总线设计法，讲述清除并有设计实例
详细介绍了单片机的总线设计法，讲述清除并有设计实例-Details of the MCU bus design method, and a design example about the removal
- 2022-11-23 12:05:03下载
- 积分：1
-
索思达基于TMS320F2812 DSP芯片的开发板 2812VM
索思达基于TMS320F2812 DSP芯片的开发板 2812VM-索思达based on TMS320F2812 DSP chip development board 2812VM
- 2022-03-03 07:29:41下载
- 积分：1
-
在点阵式液晶显示器上显示字符
在点阵式液晶显示器上显示字符-in dot-matrix liquid crystal display characters on the show
- 2023-02-05 03:05:04下载
- 积分：1
-
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序,...
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.
- 2023-08-01 05:40:03下载
- 积分：1
