-
液晶显示模块在 STM32
这是程序配置液晶显示器在STM32。
该计划是写在KEIL
- 2022-03-18 03:03:37下载
- 积分：1
-
EasyARM2131 one source development board
EasyARM2131开发板源码之一-----------4．GPIO输入实验－按键输入检测-EasyARM2131 one source development board----------- 4. Experimental GPIO input-input buttons Detection
- 2022-04-22 17:58:27下载
- 积分：1
-
ARM7
ARM7-LPC2148的PWM实验源码-ARM7-LPC2148" s PWM test source
- 2022-08-22 03:35:01下载
- 积分：1
-
LPC214X系列ARM在KEIL编译环境下的所以例程
LPC214X系列ARM在KEIL编译环境下的所以例程-LPC214X ARM series in KEIL compiler environment so the routines
- 2022-08-22 18:13:35下载
- 积分：1
-
ezflash_x5 jtag program
ezflash_x5 jtag program
- 2023-08-19 18:30:03下载
- 积分：1
-
FIC8120 方案 Multi
FIC8120 方案 Multi-ICE-FIC8120 program Multi-ICE
- 2022-03-16 21:49:59下载
- 积分：1
-
用于转换曼彻斯特编码的波形显示，可用16进制方式转为曼彻斯特编码，也可以将曼彻斯特编码转为16进制，分析波形非常好的工具，使用非常方便。...
用于转换曼彻斯特编码的波形显示，可用16进制方式转为曼彻斯特编码，也可以将曼彻斯特编码转为16进制，分析波形非常好的工具，使用非常方便。-conversion Manchester encoding for the waveform, can be 16 to 229 Manchester encoding method, Manchester can also be coded to 16 229, waveform analysis of very good tools, very convenient.
- 2022-07-18 21:39:02下载
- 积分：1
-
mnsc znskcjdasdasdasdaszxcxzc
czsczclksdncolsasdcasepojcseadcjsdvp; jdspovjmdscpom v ； 厘米 ； lzxc ； lzxmdciodfhjviowehfehws8w8fche98doshec9odhscohsacohindpicjaeicj
- 2022-01-22 08:55:14下载
- 积分：1
-
S3C4510铰接到整个擦除闪存
对S3C4510挂接的FLASH整片擦除-S3C4510 articulated to the entire erase FLASH
- 2022-05-21 23:09:46下载
- 积分：1
-
his project was built and tested with WinAVR
his project was built and tested with WinAVR-20060125.
Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!!
To build the code, just install WinAVR and run "make" from the console in echomaster and
echoslave subdirs.
"make program" will program the device if you have a AVRISP attached.
Remember to set the AVR device to at least 8MHz. The AVR may use the programmable clock
from MC1319x, just remember to check if the MC1319x and SPI communication is working FIRST!
Otherwise you wont get any clock signal to the AVR and then you can t program it or reset
the fuses!
The MC1319x has default clock output of 32kHz so you will have to set your programmer to
a very low frequency (
- 2023-02-22 21:55:03下载
- 积分：1
