登录
首页 » Matlab » 遗传算法实例

遗传算法实例

于 2023-05-02 发布 文件大小:4.24 kB
0 48
下载积分: 2 下载次数: 1

代码说明:

分析了遗传算法的初始化,交叉变异过程;通过实际例子,对遗传算法在计算目标函数值,将二进制编码转化为十进制数,计算个体的适应值等几个方面的应用进行了详细的分析。对初学者了解遗传算法具有很好的帮助。

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • NN_Matlab7
    《神经网络理论与Matlab7实现》书籍源码( Neural Network Theory and realize Matlab7 books-source)
    2008-02-29 15:16:31下载
    积分:1
  • cordicsincos
    CORDIC sin cos algorithm 2
    2010-06-21 15:27:53下载
    积分:1
  • jbd_common
    A driver for the CMOS camera controller in the Marvell 88ALP01 cafe multifunction chip. Currently works with the Omnivision OV7670 sensor.
    2014-09-22 22:14:28下载
    积分:1
  • Toolbox_Mallat
    小波分解的Mallat快速算法 Mallat快速算法的图像分解的Matlab代码(Matlab code image decomposition Mallat fast wavelet decomposition algorithm Mallat fast algorithm)
    2014-11-27 20:39:14下载
    积分:1
  • chengxu
    小波变换进行变速箱故障诊断 首先将s1和s2信号时域谱(s1代表维修前的振动信号,s2代表维修后的振动信号),画出来进行对比,会发现s1信号的振动幅值会比较高;然后对s1和s2分别进行小波分解并画出各层的时域谱,只对比s1和s2分后的最高时域谱,s2更加的具有周期性,且幅值较小,s2周期性不够明显,且振动过于密集。分析完时域谱后开始分析频谱,首先对原信号s1和s2fft转换,得到频谱图,如图,然后再对小波分析后高频部分进行fft转换,做出频谱图。对比后我们发现,在f 2375HZ出(也就是齿轮的啮合频率),s1信号频谱幅值会有急剧的升高,然后,其谐波的幅值也会增大。所以可以推断出该维修前的增速箱的齿轮可能出现问题。(Gearbox fault diagnosis based on wavelet transform s1 and s2 first time domain signal spectrum (s1 behalf of the vibration signal before maintenance, vibration signal s2 representative of repaired), drawn comparison, you will find a signal s1 vibration amplitude will be higher then s1 and s2 respectively wavelet decomposition and draw the layers of time-domain spectrum to only a maximum time domain spectroscopy s1 and s2 points after, s2 is more cyclical and smaller magnitude, s2 cyclical enough obviously, and the vibration is too dense. End domain spectral analysis after the beginning of the spectrum analysis, the first of the original signal s1 and s2fft conversion to give the spectrum, as shown, and then after the high frequency part of wavelet analysis fft transformation to make spectrum. We found that after the comparison, at f 2375HZ out (i.e. the gear mesh frequency), there will be a sharp increase in the amplitude spectrum of the signal s1, and then, the amplitude of the ha)
    2017-01-17 19:18:02下载
    积分:1
  • hough
    实现hough变换,matlb代码,图形界面(hough transform)
    2011-05-12 17:02:18下载
    积分:1
  • CHAP4_3
    基于MATLAB中M文件编写的BP神经网络控制一阶惯性环节加大时滞系统程序(Written in MATLAB M-file based on BP neural network control to increase the delay part of the first-order inertial system program)
    2011-09-15 10:21:43下载
    积分:1
  • PWM-parameter-tuning
    应用 Ma t l a b / S i mu l i n k仿真研究了这种整流器系统的三、c参数和 P I 调节器参数对直流侧电压响应及交流侧谐波与功率因数的影响,提出了一套简单易行、规范化 的设计和参数整定方法。(Ma tlab/S i mu link simulation research of this rectifier system, c parameter and the PI regulator parameters on the response of DC voltage and AC-side harmonic and power factor, a simple, standardized design and parameter tuning.)
    2012-07-26 18:00:24下载
    积分:1
  • qam_ofdm
    This is matlab code for generation of OFDM symbol using QAM modulation scheme
    2013-11-08 19:48:57下载
    积分:1
  • image-fusion
    用matlab进行多聚焦图像融合,包括图像直接融合,傅里叶变换融合,和小波融合的源代码( multi-focus image fusion by matlab, including direct images fusion, Fourier transform integration, and wavelet fusion )
    2013-12-27 13:58:46下载
    积分:1
  • 696518资源总数
  • 105595会员总数
  • 1今日下载