-
MP3的例程，很适用的一个MP范例。也可以设计一款MP3的参考
MP3的例程，很适用的一个MP范例。也可以设计一款MP3的参考-the routines, I am an MP applicable examples. A design can also reference MP3
- 2022-03-24 05:28:34下载
- 积分：1
-
Version file for STM32F10x Firmware Library (FWLib).
* The enclosed firmware a...
Version file for STM32F10x Firmware Library (FWLib).
* The enclosed firmware and all the related documentation
* are not covered by a License Agreement, if you need such
* License you can contact your local STMicroelectronics
* office.-Version file for STM32F10x Firmware Library (FWLib).
* The enclosed firmware and all the related documentation
* are not covered by a License Agreement, if you need such
* License you can contact your local STMicroelectronics
* office.
- 2022-02-02 00:23:44下载
- 积分：1
-
STM32F103VC UCGUI3.90a SSD1963 (HY35A) µCos-II-实例
基于STM32F103VC（256兆字节）为例的Keil-MDK4.xx的项目，HY35A TFT使用SSD1963在μCOS-II/μCgui3.90a环境。我已经实现了SSD1963驱动程序到μCgui环境，让演示的工作很好，速度很快。有时，它缺乏由于一个快速访问到显示寄存器和失败，进行黑显示的显示。复位解决这些问题，它的工作原理相当不错，直到再次。此行为似乎是μCOS-II和μC-GUI3.90a的组合的一个问题。类似的实现使用μCOS-II和新μGui5.20D没有发生任何故障。嗯，我想这只是一个演示来说明如何强大的STM32F1作品和一个例子，如何SSD1963是μCGUI实施GUI。
- 2022-01-22 03:34:13下载
- 积分：1
-
chamber magicARM2410 use of WinCE5.0
magicARM2410试验箱的WinCE5.0使用说明-chamber magicARM2410 use of WinCE5.0
- 2023-02-08 13:55:04下载
- 积分：1
-
S3c44b0x下的ucgui
S3c44b0x下的ucgui-S3c44b0x the ucgui
- 2022-03-01 03:24:19下载
- 积分：1
-
NAND闪存的控制逻辑
nand flash control logic
- 2023-05-28 03:25:02下载
- 积分：1
-
24c02的读写实验，Keil工程，希望对处学者有所帮助
24c02的读写实验，Keil工程，希望对处学者有所帮助-24C02 experimental reading and writing, Keil works Department would like to help scholars
- 2022-03-25 09:26:47下载
- 积分：1
-
hffmancode队列的插入删除处理
hffmancode队列的插入删除处理 -insert delete hffmancode queue handle
- 2023-04-14 14:15:03下载
- 积分：1
-
minigui在arm下的编程环境
minigui在arm下的编程环境-MiniGUI arm in the programming environment
- 2022-06-14 13:14:45下载
- 积分：1
-
his project was built and tested with WinAVR
his project was built and tested with WinAVR-20060125.
Make sure the MCU target define in the Makefiles corresponds to the AVR you are using!!
To build the code, just install WinAVR and run "make" from the console in echomaster and
echoslave subdirs.
"make program" will program the device if you have a AVRISP attached.
Remember to set the AVR device to at least 8MHz. The AVR may use the programmable clock
from MC1319x, just remember to check if the MC1319x and SPI communication is working FIRST!
Otherwise you wont get any clock signal to the AVR and then you can t program it or reset
the fuses!
The MC1319x has default clock output of 32kHz so you will have to set your programmer to
a very low frequency (
- 2023-02-22 21:55:03下载
- 积分：1
