-
江苏电力仪表通信协议，适用于国家通用规约。
江苏电能表通信协议，适用于国网最新645-2007的规约-Jiangsu power meter communication protocol, applicable to the statute of State Grid latest 645-2007
- 2022-06-20 00:56:14下载
- 积分：1
-
FlashFlex51 Microcontroller
Control of CompactFlash Card in Memory Mode
FlashFlex51微控制器
- 2022-07-23 22:34:57下载
- 积分：1
-
基于SHT71数字温湿度传感器的采集实现，89c51
基于SHT71数字温湿度传感器的采集实现，89c51-SHT71 digital temperature and humidity sensors based on the collection of achieving, 89c51
- 2023-04-04 09:40:04下载
- 积分：1
-
单片机开发文字界面的直观汉字库
单片机开发文字界面的直观汉字库-MCU development of intuitive interface language Store
- 2022-03-18 22:08:22下载
- 积分：1
-
开发工具vs2005 语言为vc 主要功能为通过usb实现对ezusbfx2的控制，输入输出控制值得一学。...
开发工具vs2005 语言为vc 主要功能为通过usb实现对ezusbfx2的控制，输入输出控制值得一学。-Vc language development tools, vs2005 main function is to achieve ezusbfx2 through usb control, input and output control is worth a study.
- 2022-07-19 03:28:46下载
- 积分：1
-
ad转换0809的引用实例，次程序调试过，用作数字电压表，精度还不错。...
ad转换0809的引用实例，次程序调试过，用作数字电压表，精度还不错。-ad conversion of the quoted examples of 0809, sub-program debugging, and used as a digital voltage meter, accuracy was not bad.
- 2022-02-11 13:41:38下载
- 积分：1
-
让您通过VB介面，简易地测试8051上面的40Hz的RF通讯。
让您通过VB介面，简易地测试8051上面的40Hz的RF通讯。
- 2022-01-21 20:31:35下载
- 积分：1
-
8bit adc
This program is free software you can redistribute it and/or mod...
8bit adc
This program is free software you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the
Free Software Foundation either version 2, or (at your option) any
later version.-8bit adc
This program is free software you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the
Free Software Foundation either version 2, or (at your option) any
later version.
- 2022-03-16 01:41:10下载
- 积分：1
-
C51源程序，实现IAP功能，可实现嵌入式系统的自主学习功能
C51源程序，实现IAP功能，可实现嵌入式系统的自主学习功能
- 2022-10-09 01:00:02下载
- 积分：1
-
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序,...
1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.
- 2023-08-01 05:40:03下载
- 积分：1
