登录
首页 » SCM » PHILIP驱动器PCF8576驱动程序,可驱动4×40个点

PHILIP驱动器PCF8576驱动程序,可驱动4×40个点

于 2023-06-17 发布 文件大小:1.24 kB
0 887
下载积分: 2 下载次数: 1

代码说明:

PHILIP驱动器PCF8576驱动程序,可驱动4×40个点-PHILIP drive PCF8576 driver can drive 4 × 40 points

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • nRF2401的开发板电路原理图的PDF文件
    nRF2401开发板的电路原理图pdf文件-nRF2401 development board schematic circuit pdf file
    2023-06-24 19:45:02下载
    积分:1
  • IC Card operating software : AT88SCl604 chip mode of operation there are five. T...
    IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作: AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位: 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位: 当CLK为低时,在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位,而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta
    2022-05-28 08:23:00下载
    积分:1
  • 全国电子设计大赛2009个题目的意义和意义。
    2009年全国电子设计大赛的题目,富有借鉴参考的意义,题目,最新,最好!-National Electronic Design Competition in 2009 the subject of the significance of the rich experiences for the title, the latest, the best!
    2022-05-19 15:08:23下载
    积分:1
  • 基于单片机的,ds18b20调试程序。注释清楚。可移植性好。
    基于单片机的,ds18b20调试程序。注释清楚。可移植性好。-Based on SCM, ds18b20 debugger. Notes clearly. Good portability.
    2022-08-10 18:29:56下载
    积分:1
  • 普通话源设置
    华大机顶盒源码(包括所有源代码).rar-Mandarin source set-top boxes (including all source code). Rar
    2022-07-11 19:12:42下载
    积分:1
  • AT mega88 A/D转换的实现 采用的是外部中断进行控制A/D转换
    AT mega88 A/D转换的实现 采用的是外部中断进行控制A/D转换-AT mega88 A/D conversion is achieved using an external interrupt to control A/D conversion
    2022-07-06 15:20:30下载
    积分:1
  • 串口扩展LED时钟子程序,不含时间设定,可直接嵌入串口LED显示系统中...
    串口扩展LED时钟子程序,不含时间设定,可直接嵌入串口LED显示系统中-Serial LED clock subroutine expansion, excluding the time settings, can be directly embedded in the serial LED display system
    2022-02-15 07:30:05下载
    积分:1
  • himself wrote the CH452 drive with the Keil C51 write
    自己写的CH452的驱动,用keil C51写的-himself wrote the CH452 drive with the Keil C51 write
    2022-09-19 13:25:03下载
    积分:1
  • 1. 本程序实现了两个功能,即6264的随机读与写 2. 实现对同一端口既作输出又作输入,如程序中 PORTA作为数据输入输出口; 3. 测...
    1. 本程序实现了两个功能,即6264的随机读与写 2. 实现对同一端口既作输出又作输入,如程序中 PORTA作为数据输入输出口; 3. 测试接线方式见Proteus仿真文件。-1. This procedure has two functions, that is, 6264 randomized read and write 2. To achieve the same port for both output also for input, such as PORTA process as a data input and output port 3. Test Connection documents, see Proteus simulation.
    2023-06-19 04:50:04下载
    积分:1
  • LED显示功能,以及步进电机的驱动程序,看程序运行…
    LED的显示功能,以及步进电机的驱动程序,打开程序后见程序中的I/O的备注就可以,只作为参考-LED display function, as well as stepper motor drivers, see the procedure to open procedure in the I/O
    2022-07-17 20:21:17下载
    积分:1
  • 696518资源总数
  • 106155会员总数
  • 8今日下载