-
便，且能进行大信息量的字符显示,还可以实现图形及曲线的显示,这就使人机接口更友好。当然，不同型号的液晶模块的内置控制器有很多种,各套指令也有一定差异, 但其设计...
便，且能进行大信息量的字符显示,还可以实现图形及曲线的显示,这就使人机接口更友好。当然，不同型号的液晶模块的内置控制器有很多种,各套指令也有一定差异, 但其设计思路和流程基本相同-Will be able to carry out large amount of information displayed characters, but also realize the display of graphics and curves, which is more friendly interface. Of course, different models of LCD module has a variety of built-in controller, the sets of commands have certain differences, but its design is basically the same ideas and flow
- 2022-03-10 20:10:12下载
- 积分：1
-
FSTN LCD driver:ST7565P,显示驱动程序源代码.
FSTN LCD driver:ST7565P,显示驱动程序源代码.-FSTN LCD driver: ST7565P, display driver source code.
- 2022-03-26 09:51:07下载
- 积分：1
-
STM32的FSMC驱动TFT液晶显示屏
STM32 FSMC 驱动TFT LCD-STM32 FSMC drive TFT LCD
- 2023-07-23 12:20:04下载
- 积分：1
-
SCM C program design and application examples
单片机C程序设计及应用实例的例子-SCM C program design and application examples
- 2022-02-05 09:32:10下载
- 积分：1
-
c51c51c51c51c51c51c51c51c51c51c51c51
单片机简易时钟 单片机简易时钟 单片机简易时钟 -c51c51c51c51c51c51c51c51c51c51c51c51
- 2023-02-20 23:00:04下载
- 积分：1
-
CC1000 RF芯片的初始化及发送程序，C语言
CC1000 RF芯片的初始化及发送程序，C语言-CC1000 RF chip initialization and sending process, C language
- 2022-03-18 20:26:38下载
- 积分：1
-
IC Card operating software : AT88SCl604 chip mode of operation there are five. T...
IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta
- 2022-05-28 08:23:00下载
- 积分：1
-
PDIUSBD12 USB1.1 C51 source code
PDIUSBD12 USB1.1 C51源代码-PDIUSBD12 USB1.1 C51 source code
- 2022-02-25 11:31:09下载
- 积分：1
-
Development and application of single
MSP430单片机开发应用实例代码，适合任何型号-Development and application of single-chip MSP430 code examples for all models
- 2022-03-30 02:21:50下载
- 积分：1
-
freescale单片机HCS12对12864的驱动，能显示汉字，ASCII字符，以及绘图等。
freescale单片机HCS12对12864的驱动，能显示汉字，ASCII字符，以及绘图等。-Freescale HCS12 of 12864 single-chip driver, can display Chinese characters, ASCII characters, as well as graphics and so on.
- 2022-07-19 05:25:08下载
- 积分：1
