登录
首页 » 嵌入式系统 » S3C2440处理器上的CF卡读写程序,已经通过验证。

S3C2440处理器上的CF卡读写程序,已经通过验证。

于 2023-07-19 发布 文件大小:2.94 kB
0 128
下载积分: 2 下载次数: 1

代码说明:

S3C2440处理器上的CF卡读写程序,已经通过验证。-S3C2440 processor CF card reader procedure has been validated.

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • LG 手机文件夹列表和删除
    在嵌入式系统中使用此程序。 此程序写的 C 语言到上市的文件夹在 LG 手机: 手机短信、 电话簿、 图片、 游戏、...... 程序从手机读取数据后,它将删除所有的私有数据,在您的手机中。
    2022-12-16 18:45:03下载
    积分:1
  • 代码为linux下关于pci_skel驱动,程序比较简单,但结构比较清晰,对刚学习 LINUX下驱动开发人员很有帮助...
    代码为linux下关于pci_skel驱动,程序比较简单,但结构比较清晰,对刚学习 LINUX下驱动开发人员很有帮助-Code for pci_skel drivers under linux, the program is relatively simple, but relatively clear structure, just under the drive to learn LINUX Developer helpful
    2023-03-14 16:25:03下载
    积分:1
  • 红外遥控器已被广泛使用在各种类型的家电产品上,它的出现给使用家器提供了很多的便利。红外遥控一般由红外发射装置和红外接受设备两大部分组成。红外发射装置又可由键...
    红外遥控器已被广泛使用在各种类型的家电产品上,它的出现给使用家器提供了很多的便利。红外遥控系统一般由红外发射装置和红外接受设备两大部分组成。红外发射装置又可由键盘电路、红外编码芯片、电源和红外发射电路组成。红外接收设备可由红外接收电路、红外解码芯片、电源和应用电路组成。通常为了使信号能更好的被传输发送端将基带二进制信号调制为脉冲串信号,通过红外发射管发射。本设计采用Atmega8作为红外发射编码和接收解码芯片。-Infrared remote control has been widely used in various types of household electrical appliances, it" s there to provide the users a lot of convenience. Infrared remote control system in general by the infrared emission devices and infrared devices to accept the composition of two major parts. Infrared emission circuit device can be by keyboard, infrared encoder chip, power and infrared emission circuit. By the infrared receiver infrared receiver circuit equipment, infrared decoder chip, power supply and application circuit. Usually better in order to signal the sending end of the transmission to binary base-band signal for pulse modulation, through the launch tube infrared emission. The design uses infrared emission Atmega8 as encoding and decoding chip receiver.
    2022-05-06 14:11:23下载
    积分:1
  • SD卡FAT文件,很方面移植,注释详细
    SD卡FAT文件系统,很方面移植,注释详细-SD Card FAT file system, it is aspects of transplantation, detailed notes
    2023-04-06 19:35:03下载
    积分:1
  • 基本放大器电路原理图的基本工作原理…
    基本的放大器电路放大器的基本工作原理图解法分析等几种分析方法-Basic amplifier amplifier circuit diagram of the basic working principle of analysis of several analytical methods such as
    2022-06-13 09:17:03下载
    积分:1
  • pdiusbd12的固件程序
    pdiusbd12的固件程序-pdiusbd12 firmware procedures
    2023-08-24 22:20:04下载
    积分:1
  • 主要涉及ad7799寄存器的读写,各种寄存器的配置
    主要涉及ad7799寄存器的读写,各种寄存器的配置-read and write of ad7799 register
    2022-02-25 17:12:59下载
    积分:1
  • outlined transformer
    变压器概述-变压器经典文章(中文PDF)-outlined transformer- transformer classic article (Chinese PDF)
    2022-02-11 19:26:22下载
    积分:1
  • This procedure for the experiment board' s overall test program, a comprehens...
    本程序为实验板的总体测试程序,综合测试了整个实验板上的绝大多数功能,下载程序后会依次看到以下5种状态。 1.8个流水灯先会从上到下流动一遍,同时蜂鸣器发声。 2.接着DAC电流指示灯由暗变亮 3.接着前三位数码管显示温度值 4.接着AD数值显示在数码管的前三位 5.接着等待矩阵键盘的按下,按下后相应的数码显示在数码管的后三位上-This procedure for the experiment board" s overall test program, a comprehensive test of the vast majority of the entire experiment on-board features, download the program will in turn see the following five kinds of states. 1.8 water lights will first flow from top to bottom again, at the same time buzzer sound. 2. And then DAC current indicator light changes from the dark 3. And then the top three LED display temperature 4. And then AD values displayed in the top three digital tube 5. And then wait for the keyboard matrix is pressed, press the corresponding post- digital display in the digital control on the latter three
    2023-08-29 01:00:04下载
    积分:1
  • eda技术的说明,程序VHDL(电梯键扫交通灯步进电机)CPLD/FPGA
    eda技术的说明,程序VHDL(电梯键扫交通灯步进电机)CPLD/FPGA-EDA description of the techniques, procedures VHDL (elevator button sweep stepper motor traffic lights) CPLD/FPGA
    2022-12-31 06:20:03下载
    积分:1
  • 696516资源总数
  • 106913会员总数
  • 8今日下载