w77e58 双串口 液晶显示源程序 c语言编写-w77e58 dual serial LCD source language c

使用单片机C8051F330对无线发射接收模块进行配置与控制,使组件成为无线通讯中的终端,可与基站进行双向通讯-C8051F330 use single-chip wireless transceiver and control module configured to enable wireless communications components to become the terminal, with the base station two-way communication

IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta

凌阳单片机模拟6800时序，很多液晶的驱动可以用的上。-Sunplus simulated 6800 time series, a lot of LCD driver can be used on.

一个液晶显示器TX240128程序。我把我小孩的相片做在上面了，如果你用51的片子就能调试你的显示器了。端口连接在程序中有定义。你看下就知道了哈！-A liquid crystal display TX240128 procedures. I put my kids to do in the photo above, if you use the 51 films will be able to debug your display has. Port in the procedure definition. You know facie Ha!

基于并口的SPI总线93CXX的读写程序-This is a programm for SPI chip 93cxx in use of parral port

一个LCD菜单绘图程序，通过点阵显示图片，也可显示动态图象！-An LCD menu drawing procedures, through the dot-matrix display images, dynamic images can also be displayed!

一个简单的VB界面程序,包括按钮,文本等,此程序是一个CanOpen通讯的上位机界面,通过提供的接口函数,进行数据的接收和发送.希望对学习VB的有所帮助.-A simple VB interface procedures, including buttons, text, etc., this program is a PC CANOpen communication interface, by providing the interface function, to receive and transmit data. I hope to learn from the VB help.

这是一个就算波特率的软件，功能强大，在单片机通信时不用自己动手计算，只要用此软件点击一下，就能得到结果。-This is a software that even if the baud rate, powerful, in the MCU communicate without it-yourself basis, as long as the click with this software, you can get results.

单片机控制AD2543,同时通过液晶显示的程序，通过移植修改即可以应用-SCM AD2543, at the same time through the liquid crystal display procedures, through the graft modification can be applied