-
matlab编写的jacks模型多径衰落信道模型，主要用的sum
matlab编写的jacks模型多径衰落信道模型，主要用的sum-of-sinusoids方法-matlab prepared jacks model multipath fading channel model, mainly used in sum-of-sinusoids method
- 2022-11-29 11:20:03下载
- 积分：1
-
包含两篇关于FXO、FXS的文档，详细介绍了他们的区别和定义，是开发VOIP设备的很好的参考材料。这种材料可是很难找哦。...
包含两篇关于FXO、FXS的文档，详细介绍了他们的区别和定义，是开发VOIP设备的很好的参考材料。这种材料可是很难找哦。-contains two of FXO, FXS document, detailing their differences and definitions, the development of VoIP equipment is a good reference material. But this material is difficult to find, oh.
- 2022-02-02 17:11:15下载
- 积分：1
-
手机顶尖游戏制作全揭密
手机顶尖游戏制作全揭密-top mobile phone game, Colo.
- 2022-01-25 19:37:32下载
- 积分：1
-
procedures given CAN Bus Interface communications MATLAB simulation code, hope y...
程序给出了CAN总线接口的通讯的MATLAB仿真代码,希望能给大家提供帮助.-procedures given CAN Bus Interface communications MATLAB simulation code, hope you can help.
- 2022-03-21 13:30:35下载
- 积分：1
-
串口模块 适用于VB.Net VC++ C# 比VB6的串口控件好用
串口模块 适用于VB.Net VC++ C# 比VB6的串口控件好用-serial module applicable to the C# VB VC than VB6 Serial Control Easy
- 2022-05-28 04:47:08下载
- 积分：1
-
误码率仿真讲义，在matlab环境中如何进行接收数据的误码率计算...
误码率仿真讲义，在matlab环境中如何进行接收数据的误码率计算
- 2023-03-07 16:45:04下载
- 积分：1
-
多方会话消息之实例讲解
多方会话消息之实例讲解 -multi-session news examples to explain the m ulti-session news examples will explain the multi- so news on the case
- 2022-08-23 09:58:50下载
- 积分：1
-
认知无线电网络
应用背景最近，认知无线电技术已经被提出作为未来的无线通信的关键技术利用动态频谱接入策略的通信。这提供了更灵活的方式利用无线基于固定频谱接入策略的频谱比传统无线电技术。认知无线电网络（CRNs），获得信道频谱空洞的信息，谈判的主用户和次之间用户对频谱分配、同步传输参数是铬介质访问的重要功能控制协议。在本文中，我们讨论了MAC层的基本职责和CRN的功能。基本上，我们专注于调查的最新进展，在铬麦克协议，以及它们的特点特点，优点和缺点。最后，我们提供了这些协议以表格形式的主要特点。关键技术认知无线电中的动态频谱接入网络仍处于起步阶段。许多重要的和复杂问题需要解决。在本文中，我们提供了一个调查，一些铬麦克协议并讨论了它们的主要工作原理结合自身特点。
- 2022-08-21 09:57:21下载
- 积分：1
-
nothing to say! It is only the necessar file to be enabled to download other imp...
nothing to say! It is only the necessar file to be enabled to download other important file for my studies.
- 2023-01-26 04:25:03下载
- 积分：1
-
0. Install the rp
0. Install the rp-pppoe-software
--------------------------------
You should have already done this by the time you re reading this. If not,
go back and read README.
1. Set up your Ethernet hardware
--------------------------------
First, make sure the Ethernet card you intend to use with the modem is
visible to the Linux kernel. Just how to do this is beyond the scope
of this document. However, if the card is the only Ethernet card in
the system, executing:
ifconfig eth0
should display something like this:
eth0 Link encap:Ethernet HWaddr 00:60:67:62:31:D4
plust some more lines. Your HWaddr will be different. As long as you see
the HWaddr line, your card should be working.
DO NOT assign an IP address to the Ethernet card. DO NOT configure the
card to come up at boot time.-0. Install the rp- PPPOE-software-------------------------------- You should have al ready done this by the time you re reading this. I f not, go back and rea
- 2023-03-02 00:45:03下载
- 积分：1
