-
YULEWALKER
现代谱估计的YULEWALKER算法仿真(Modern Spectral Estimation Algorithm Simulation YULEWALKER)
- 2010-12-19 11:07:01下载
- 积分：1
-
bufenxiangguan
基于部分相关的捕获程序，并且通过蒙特卡罗仿真计算检测概率。(Based on the relevant part of the capture process, and by Monte Carlo simulation of probability of detection.)
- 2011-10-10 20:10:15下载
- 积分：1
-
CE803-Matlab-Tutorials
very good files for matlab beginners very good file in different fields
- 2013-04-04 06:35:08下载
- 积分：1
-
BPSK_baseband_simulink
SIMULINK下，BPSK基带传输演示，包括从发送端到接受端及信号打印。(SIMULINK under, BPSK baseband transmission demonstration, including from send-ended to the receiving end and the signal to print.)
- 2007-07-28 20:15:36下载
- 积分：1
-
qam
利用一数学仿真工具构建一16-QAM的通信系统
工具：推荐使用Matlab,可使用信号处理工具箱但不能利用通信工具箱(The use of a mathematical simulation tools to build a 16-QAM communication system tools: Recommended use of Matlab, Signal Processing Toolbox can be used but not the use of communication toolbox)
- 2009-12-16 17:06:11下载
- 积分：1
-
PSO-BP和GA-BP
分别使用PSO和GA优化BP神经网络的参数，用于非线性函数拟合(PSO and GA are used to optimize the parameters of the BP neural network for nonlinear function fitting)
- 2021-04-29 10:38:43下载
- 积分：1
-
MATLAB-lvboqisheji
基于matlab编写的小程序，可以实现观察信号的泄漏现象，亲自验证好使。(Based on matlab prepared applet, you can achieve the observed signal leakage phenomenon, personally verify so.)
- 2013-10-24 15:10:53下载
- 积分：1
-
wind
说明： 风场输入文件，FVCOM,热通量计算使用(Wind field input file, FVCOM, heat flux calculation)
- 2021-04-13 20:38:56下载
- 积分：1
-
FFT_Analysis
说明： Matlab中的fft分析含噪声的信号，其中有直接FFT，时域同步平均后FFT，频域同步平均后FFT(Matlab s fft analysis with noise signals, which have a direct FFT, time-domain synchronous average, after the FFT, frequency domain synchronization for after averaging FFT)
- 2020-12-12 16:09:15下载
- 积分：1
-
mjiaqiang1
下面是我编的一个软硬阈值去噪的matlab程序 下面是我编的一个软硬阈值去噪的matlab程序：thr=sigma*(2*lgN)1/2/lg(j+1) 用[x,xn]=wnoise(2,10,6) 产生噪声测试数据-The following is Part I of a of hard and soft threshold denoising matlab procedure is the following hardware and software, I made a threshold denoising matlab program: thr = sigma* (2* lgN) 1/2/lg (j+1) by [x, xn] = wnoise (2,10,6) noise test data(thr=sigma*(2*lgN)1/2/lg(j+1) 用[x,xn]=wnoise(2,10,6) 产生噪声测试数据-The following is Part I of a of hard and soft threshold denoising matlab procedure is the following hardware and software, I made a threshold denoising matlab program: thr = sigma* (2* lgN) 1/2/lg (j+1) by [x, xn] = wnoise (2,10,6) noise test data)
- 2012-05-20 23:01:46下载
- 积分：1
