登录
首页 » matlab » fft

fft

于 2010-01-08 发布 文件大小:1KB
0 159
下载积分: 1 下载次数: 3

代码说明:

  利用FFT算法产生2FSK,并对频率参数进行求取、分析(The use of FFT algorithms generate 2FSK, and frequency parameters to acquire, analyze)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论


0 个回复

  • short-circuit
    这个说明倒不是说明函数的功能,只是声明一下函数中出现的问题。 shortest()函数没有问题,在secshortest中我希望只得到一条次短路(或几条roadcost()值相同的次短路),结果却出来好几条,我仔细检查了一下程序,应该没有什么问题。 因此在使用时,要得到次短路,只能用roadcost()函数分别求一下各条路的权重和,找到最小的。 有些奇怪 (Note that this is not the function of function, but a statement about the problems in function. shortest () function there is no problem, I hope that in secshortest only a short time (or several roadcost () times the value of the same short-circuit), the result is several out, I carefully examined the process, it should be no problem. Therefore, in use, to be at a short circuit can only be used roadcost () function, respectively, for some of the weight of the road and find the smallest. Some strange)
    2009-05-21 21:11:51下载
    积分:1
  • xyz2enu
    用于坐标转换,由xyz转换到neu方向上,基于MATLAB编程实现(Used for coordinate conversion the conversion by xyz neu direction, based on MATLAB Programming)
    2021-03-28 16:39:11下载
    积分:1
  • iii
    Add Gaussian white noise (mean=0 and variance=0.05 ) to the image using imnoise command. Now use fftshift command to put all zero frequencies in the middle. Low-pass filter this function by applying a mask saving only the central Fourier coefficients. Set the mask width to 255 and create the filtered image.
    2014-09-11 15:08:58下载
    积分:1
  • dbf100zhenlie
    100天线阵列1期望信号2干扰信号,用LMCV自适应波束形成(100 antenna array desired signal interference signals, adaptive beam formation LMCV)
    2013-05-08 10:49:52下载
    积分:1
  • MIPI-Alliance-Specification-for-Camera-Serial-Int
    MIPI Interface Introduction
    2013-12-16 13:48:00下载
    积分:1
  • Bouc-Wen
    Bouc-Wen非线性滞回模型仿真程序,通过此程序可观察Bouc-Wen模型中各参数对其所描述的滞回曲线形状的影响(Bouc-Wen nonlinear hysteretic model simulation program, described by the Bouc-Wen model parameters on the hysteresis curve shape can be observed through this program)
    2021-04-08 16:19:01下载
    积分:1
  • 基于Weber和simulink的齿轮啮合刚度计算
    说明:  使用weber算法计算齿轮啮合刚度,具有重大意义。(It is of great significance to use the weber algorithm to calculate the gear mesh stiffness.)
    2020-07-13 15:38:53下载
    积分:1
  • 一类Bessel方Matlab序源代码
    主要阐述的是使用差分法解一类Bessel方程在不同边界条件下的离散解(elaborated in the main difference is the use of a solution like Bessel equation in different boundary conditions of the Discrete Solutions)
    2005-04-02 14:55:34下载
    积分:1
  • MATLABIMAGEPROCESSINGCOMMAND
    该文档里面包含了MATLAB里常用的命令及例子,介绍的非常详细。(The document which contains a MATLAB command that is commonly used and examples described in great detail.)
    2009-11-08 14:46:20下载
    积分:1
  • KPCA故障检测序(代码已优化)
    基于核主元分析(KPCA)的工业过程故障检测,代码已优化,运行效率高,有详细的注释,附有训练数据和测试数据。(Achieves fault detection of industrial processes based on Kernel Principal Component Analysis (KPCA); the code has been optimized for high operational efficiency; detailed notes are attached with training data and test data.)
    2018-03-17 09:32:11下载
    积分:1
  • 696518资源总数
  • 105133会员总数
  • 27今日下载