-
MATLABR2007jichujiaocheng
关于MATLAB初学的文档，对初学MATLAB应该会有比较大的帮助！(Documentation on MATLAB beginner, for beginners should be larger MATLAB help!)
- 2010-05-19 10:10:32下载
- 积分：1
-
tracking.rar
use a three order loop to track the GPS L2C signal, could be useful for beginner
- 2011-05-17 13:43:28下载
- 积分：1
-
read-eight-data
一个用于从Physiobank中读取8导心电信号的MATLAB程序(Read used from Physiobank in a 8-lead ECG MATLAB program)
- 2013-03-24 20:51:59下载
- 积分：1
-
incremental_svm
这个套件包含了C + +实现"减量和增量支持向量机学习"，根据Cauwenberghs和Piggio他们的matlab实现。(This package contains a c++ implementation of "Incremental and Decremental Support Vector Machine Learning, Cauwenberghs and Poggio" based on their
matlab implementation.
Getting started
- make (to compile)
- ./inc_svm 1 data_kernel.txt (to train and cross-validate)
- ./inc_svm 1 diabetes_kernel.txt)
- 2012-05-11 03:48:10下载
- 积分：1
-
Diffusion-k-tensor-Estimation
Diffusion k-tensor Estimation from Q-ball imaging using discretized principal axes
- 2013-11-16 10:14:44下载
- 积分：1
-
bif
该MATLAB程序主要用于绘制微分方程的分岔图。(The MATLAB program is mainly used to draw the bifurcation diagram of the differential equations.)
- 2012-11-22 19:20:59下载
- 积分：1
-
l1ioftb2
该算法非常适用于正系统、正切换系统等仿真(NUMERICAL SIMULATION FOR POSITIVE SYSTEMS and positive switched system)
- 2018-12-24 16:10:25下载
- 积分：1
-
项目4
说明： 任务：设计一个4×2.5Gbit/s 长距离光纤传输系统，并利用OptiSystem 仿真验证。
要求：
1．采用波分复用技术，波长设置以100GHz 为间隔，频率分别为193.1THz、193.2THz、193.3THz、193.4THz，每个波长传输速率为2.5Gbit/s（NRZ），传输距离为300km。采用常规光纤，光纤损耗系数为0.25dB/km。
2．单通道光发送机最大输出功率为0dBm，光接收机的接收光功率不低于－26dBm，过载点为－10dBm。
3．可以采用EDFA 作为线路放大器，其中EDFA 的输入功率限制在－18～2dBm，最大输出功率20dBm，增益范围为13～25dB，噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify.
Requirement:
1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km.
2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm.
3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)
- 2019-05-13 09:39:41下载
- 积分：1
-
mchap8
MATLAB插值与数据拟合、样条插值与数值微积分、由已知数据拟合数学模型、信号分析与数字信号处理基础(MATLAB interpolation and data fitting, spline interpolation and numerical calculus, from the known data fitting mathematical model, signal analysis and digital signal processing-based)
- 2009-11-16 09:56:38下载
- 积分：1
-
Tx2_Rx1
采用两发一收的空时分组码经过瑞丽信道后的性能仿真。(The use of a collection of two space-time block codes through Ruili performance after channel simulation.)
- 2009-04-17 20:21:18下载
- 积分：1
