-
3线双向零等待IO通讯机制 单片机通讯源代码带说明
3线双向零等待IO通讯机制 单片机通讯源代码带说明-3 bidirectional zero waited for the IO communication
machine-made monolithic integrated circuit communication source code
belt explained
- 2022-10-28 10:20:03下载
- 积分：1
-
MCS51控制1602字符型LCD的源代码
MCS51控制1602字符型LCD的源代码-MCS51 control 1602 Character LCD source code
- 2022-01-26 05:29:05下载
- 积分：1
-
W3100是WIZnet公司专门为以太网互联和嵌入式设备推出的硬件TCP／IP协议栈芯片，其硬件TCP／IP协议栈包含了TCP、UDP、IP、ARP和ICMP协...
W3100是WIZnet公司专门为以太网互联和嵌入式设备推出的硬件TCP／IP协议栈芯片，其硬件TCP／IP协议栈包含了TCP、UDP、IP、ARP和ICMP协议，这是他的indirect模式的原码-WIZnet W3100 is designed for the Internet and Embedded Ethernet equipment introduced hardware TCP/IP protocol stack chips, and hardware TCP/IP protocol stack includes TCP, UDP, IP, ICMP and ARP agreement, it is his indirect model of the original code
- 2022-08-09 10:14:34下载
- 积分：1
-
51单片机C程序，花自动演奏和键盘性能…
51单片机的电子琴C程序有自动演奏和键盘演奏功能-51 Microcontroller, the flower C program for automatic playing and keyboard performance features
- 2022-03-20 05:57:12下载
- 积分：1
-
MSP430对SD卡驱动程序，C语言，运行环境IAR
MSP430对SD卡驱动程序，C语言，运行环境IAR-SD card driver program
- 2023-04-26 10:00:03下载
- 积分：1
-
基于触摸屏校准程序ARM7开发系统，COD…
基于ARM7开发系统的触摸屏校准程序，代码中有详细的中文注释，方便用户移植……-ARM7 development system based on the touch screen calibration procedures, a detailed code of the Chinese Notes user-friendly transplantation -ARM7 Development System Based on the touch screen calibration procedure, the code in detail the Chinese notes, user-friendly transplantation ... ...-ARM7 development system based on the touch screen calibration procedures, a detailed code of the Chinese Notes user-friendly transplantation
- 2022-04-27 09:36:04下载
- 积分：1
-
nRF9E5的性能测试程序,该程序控制开发板的一个灯的亮与灭.
nRF9E5的性能测试程序,该程序控制开发板的一个灯的亮与灭.-nRF9E5 the performance test procedures, the control of a development board with the bright lights out.
- 2022-07-05 12:14:37下载
- 积分：1
-
凌阳单片机的语音程序3，供学习凌阳单片机的学习者参考
凌阳单片机的语音程序3，供学习凌阳单片机的学习者参考-Sunplus voice SCM three procedures for learning Sunplus SCM reference learners
- 2022-02-07 01:24:51下载
- 积分：1
-
1.将P1.0～P1.3接开关，将P1.4～P1.7接发光二极管。依据P1.0～P1.3开关状态控制P1.4~P1.7发光二极管点亮。 2.将P1.0～P1.7...
1.将P1.0～P1.3接开关，将P1.4～P1.7接发光二极管。依据P1.0～P1.3开关状态控制P1.4~P1.7发光二极管点亮。 2.将P1.0～P1.7全部接发光二极管，开始P1.0、P1.5点亮，左循环50次后P1.1、P1.4点亮；右循环30次，循环往复。-1. P1.0- P1.3 will then switch to P1.4- P1.7 access LEDs. P1.0- P1.3 based on state control switch P1.4- P1.7 LED lights. 2. P1.0- P1.7 will take all LEDs started Schematic, P1.5 lit, the left circle after 50 P1.1 and P1.4 lit; Turn right circle 30 times repeated.
- 2022-03-07 10:38:31下载
- 积分：1
-
PIC
基于PIC单片机877的电动自行车控制器的开发原理及源程序。-PIC-based single-chip controller 877 of the electric bicycle and the development of the principle source.
- 2022-08-09 15:25:42下载
- 积分：1
