登录
首页 » Verilog » 四位数码管1~9999加法计数

四位数码管1~9999加法计数

于 2022-02-07 发布 文件大小:500.99 kB
0 88
下载积分: 2 下载次数: 1

代码说明:

verilog HDL语言程序,运行后实验板四位数码管依次加法计数,从1到9999计数,超过后即溢出,重新从1开始 计数

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • U_XMIT
    8位并行转穿行发送程序,波特率可自行设置,经检验有实用效果(8-bit parallel transfer walk through the sending program, the baud rate can be set up their own practical effect inspection)
    2013-03-15 19:05:49下载
    积分:1
  • dl.sh
    linux cmd line download script
    2012-03-15 02:51:11下载
    积分:1
  • dma_ahb
    挂靠在AMBA2.0的AHB总线上的DMA装置,用于直接发起数据传输。(Anchored the DMA devices the AHB bus AMBA2.0, for initiating data transfer.)
    2021-03-29 21:49:10下载
    积分:1
  • full adder
    说明:  vhdl code for full adder
    2020-06-30 22:46:55下载
    积分:1
  • SDRAM-control
    好用的SDRAM控制器,经过FPGA平台验证过。(It is a SDRAM controller with verilog code. It is a good code, and confirmed.)
    2018-10-08 18:07:55下载
    积分:1
  • waveform-generator-o-VHDL-program
    实现4种常见波形正弦、三角、锯齿、方波(A、B)的频率、幅度可控输出(方波 --A的占空比也是可控的),可以存储任意波形特征数据并能重现该波形,还可完成 --各种波形的线形叠加输出。 (Achieve the four kinds of common sine wave, triangle, sawtooth, square wave (A, B) the frequency and amplitude controlled output (square wave- A duty cycle is controlled), can store arbitrary waveform feature data and can to reproduce the waveform, it can perform- all kinds of linear superposition of the output waveform.)
    2009-10-08 09:56:59下载
    积分:1
  • dpim_circle
    dpim是光通信中使用的一种调制方式,这里提供的是它的环回代码,自己可以根据需要拆开了下载到两块板子上。(dpim is used in an optical modulation, here is its loop-back code, they can download needed two apart on the board.)
    2011-05-25 16:02:51下载
    积分:1
  • signal
    能产生正弦波、三角波、方波和e指数衰减的扫频波,且相关参数可调(Can produce sine wave, triangle wave, square wave, and e exponential decay wave sweep and adjustable parameters)
    2014-05-13 15:15:12下载
    积分:1
  • 11bit_Barker_code
    说明:  设计11位巴克码序列峰值检测器,巴克码相关器原理:巴克码相关器能够检测巴克码序列峰值,并且能够在1bits错误情况下检测巴克码序列峰值。(A 11-bit Barker code sequence peak detector is designed. The principle of Barker code correlator is that the Barker code correlator can detect the peak value of Barker code sequence and detect the peak value of Barker code sequence in the case of 1 bits error.)
    2020-06-21 14:00:01下载
    积分:1
  • GPIO的RTL代码
    资源描述通用输入/输出(GPIO) ;在 通用集成电路引脚; ;其行为包括无论是输入或输出引脚可由用户在运行时间 。GPIO引脚没有预定的目的,而去使用默认的。其思想是,有时一个系统集成商,建立一个完整的系统可能需要一把额外的数字控制线,并有这些可从一个芯片,避免了安排额外的电路,以提供他们。例如, ;realtekalc260芯片(音频编解码器)有8个GPIO引脚,从而去使用默认的。一些系统集成商(宏碁公司 ;笔记本电脑)使用第一个GPIO(GPIO0)在打开的alc260  ;放大器 ;用于笔记本电脑的内置扬声器和耳机插孔外 。
    2022-09-07 07:35:03下载
    积分:1
  • 696518资源总数
  • 105559会员总数
  • 1今日下载