-
ROAM-LOD
ROAM Simplistic Implementation
By Bryan Turner
brturn@bellsouth.net
January, 2000
Project file for MS Visual C++ 6.0.
Requires GLUT DLL (www.opengl.org)
Adjust program constants in Landscape.h and Utility.cpp.
MAPS:
Default map is read from HeghtXXX.raw where XXX is the MAP_SIZE
(as defined in Landscape.h). If this map is not found, the program
attempts to open "Map.ved", a Tread Marks map file. Tread Marks maps
will only work for MAP_SIZE == 1024. Also, the MULT_SCALE to view
Tread Marks maps correctly is "0.25f". (www.TreadMarks.com)
CONTROLS:
MOUSE - Hold Left Mouse Button to Rotate View Angle
Q - Change Rendering Mode (Wireframe, Lit, Fill, Texture)
O - Change View Mode (Observe, Follow, Drive, Fly)
W/S - Move forward/back
A/D - Rotate left/right (in Observe Mode only)
F - Stop Animation
R - Toggle Frustum Drawing
0/9 - More/Less Triangles per frame
1/2 - Adjust FOV(ROAM Simplistic Implementation
By Bryan Turner
brturn@bellsouth.net
January, 2000
Project file for MS Visual C++ 6.0.
Requires GLUT DLL (www.opengl.org)
Adjust program constants in Landscape.h and Utility.cpp.
MAPS:
Default map is read from HeghtXXX.raw where XXX is the MAP_SIZE
(as defined in Landscape.h). If this map is not found, the program
attempts to open "Map.ved", a Tread Marks map file. Tread Marks maps
will only work for MAP_SIZE == 1024. Also, the MULT_SCALE to view
Tread Marks maps correctly is "0.25f". (www.TreadMarks.com)
CONTROLS:
MOUSE- Hold Left Mouse Button to Rotate View Angle
Q- Change Rendering Mode (Wireframe, Lit, Fill, Texture)
O- Change View Mode (Observe, Follow, Drive, Fly)
W/S- Move forward/back
A/D- Rotate left/right (in Observe Mode only)
F- Stop Animation
R- Toggle Frustum Drawing
0/9- More/Less Triangles per frame
1/2- Adjust FOV)
- 2008-09-26 11:28:06下载
- 积分：1
-
PT8211(orTM)2Ch16BitDAC_CtrlFuncWritebyC51)
PT8211/TM8211 2通道16bitDAC控制函数，
包含了完整的控制流程和调用实例。(PT8211/TM8211 2-channel 16bitDAC control functions, including a complete control flow and call instance.)
- 2020-12-21 11:29:08下载
- 积分：1
-
Dot-Matrix-5x7-(1)
Dot Matrix 5 x 7 sample progmam , hope you enjoy
- 2012-12-11 10:33:42下载
- 积分：1
-
Hex_to_ASCII
十六进制转ASCII码的一段子程序。。。(ASCII code hex switch to a subroutine.)
- 2010-12-31 23:14:01下载
- 积分：1
-
维纳滤波
维纳滤波程序维纳滤波程序维纳滤波程序维纳滤波程序维纳滤波程序维纳滤波程序维纳滤波程序维纳滤波程序维纳滤波程序维纳滤波程序维纳滤波程序维纳滤波程序
- 2022-02-02 10:54:47下载
- 积分：1
-
Qt下的扫雷软件
使用qt做的模仿windows的扫雷游戏，有三个难度可以调节，基本还原了原版扫雷的效果。运行流畅，自带扫雷音效。
- 2022-02-05 02:33:43下载
- 积分：1
-
安全芯片代码
基于DDA网络通讯加密的需求，DDA网络导入加密系统。
加密芯片：RJMU101S
最小加密系统构成：1）业务主控MCU+加密模块（加密模块=加密主控MCU+加密芯片）
2）后台+USBKEY（USBKEY=加密主控MCU+加密芯片）
加密模块内部通讯接口：SPI
加密模块外部通讯接口：UART
加密模块主控MCU额外硬件资源要求：1路主SPI,一路UART，
&nb
- 2022-04-02 01:22:39下载
- 积分：1
-
ARMImage_uCOSII_lpc2131
ucos移植到lpc2131的arm模板(OUT transplanted to the arm template lpc2131)
- 2006-09-08 23:46:19下载
- 积分：1
-
optimize-
键是一种标准零件,通常用来实现轴与轮毂之间的周向固定以传递转矩，有的还能实现轴上零件的轴向固定或轴向滑动导向。在键连接设计时，间的高度和宽度根据轴的直径d选取，而键长L则根据轴上零件轮毂宽度B而定，通常L=B-（5—10）mm。键的尺寸确定后，再进行强度校核。而为了保证绝对安全，键的尺寸取值往往都趋于保守，所选键的尺寸大。本程序采用优化设计方法，在满足强度要求的前提下求出键的最小结构尺寸，证明键宽b和键高h的取值可以小于标准值。(Key is a standard part, often used to achieve between shaft and hub to transfer torque to a fixed week, and some can achieve a fixed axis or axial parts of the axial sliding direction. Key connection in the design, height and width between the shaft diameter d according to selection, and the bond length L is based on the width of the wheel shaft parts B and, typically L = B-(5-10) mm. Key size is confirmed, then strength check. In order to guarantee absolute security, key size values ??are often conservative, the size of the selected key to big. The program uses optimization methods to meet the strength requirements of the derived key premise of the minimum structure size, proved key width b and height h of the key values ??can be less than the standard value.)
- 2011-09-05 20:16:03下载
- 积分：1
-
circle
a simple graphics application
- 2014-02-06 14:23:28下载
- 积分：1
