该程序是本人学习单片机期间针对2片SED1520编写的122X32点阵液晶驱动.内附详细注释.-This source code is the driver of 2 pieces SED1520. Attached includes notes in detail.

注:protel电路图 1.INPUT12为高压气压和低压压传感器输入端. 2.OUTPUT为充气输出控制端. 3.当高低压有接地信号时,电机正转,气阀打开. 4.INPUT2低气压时有信号时,充气OUTPUT输出,充气电机转. 5.RS1与RS2是调节阀门距离用地 6.RS3是与气阀电机同步时,是气阀电机的转动圈数传感器. 7.RS4是调节延时时间用地-Note: protel circuit 1.INPUT12 and low-voltage high-pressure pneumatic pressure sensor input. 2.OUTPUT output control for the inflated side. 3. When the high and low pressure have a grounding signal when the motor is transferred, the valve opens. 4.INPUT2 low pressure when there is signal output OUTPUT inflatable, inflatable motor switch. 5.RS1 and RS2 is the regulator valve from the land 6.RS3 synchronous motor with the valve, the valve motor is rotating circle the number of sensors. 7.RS4 delay time to regulate land

老外写的基于arm的sd/mmc读写程序，开源的项目-foreigner was based arm of sd/-3.4 reading and writing procedures, open-source project

本设计采用凌阳16 位单片机SPCE061A对步00进电机进行控制，通过IO口输出的具有时序的方波作为步进电机的控制信号，信号经过芯片L298N驱动步进电机；-This design uses 16-bit single-chip Sunplus SPCE061A to step into the motor control 00, through the IO port with the output timing of the square wave as a stepper motor control signal, the signal after the chip stepper motor driver L298N

把所有端口的同时置高置低,不断闪烁 2 p1 口3 路流水灯理解2 进制数与端口的关系 3 单片机的加法:把52h+0fch 结果送p1 口 4 单片机的乘法:把ff*03h 结果送p1 5 单片机的二进制加法 6 单片机的两位计数器 7 学习单片机的逻辑运算 8 进一步学习单片机的逻辑运算 9 循环移位指令的流水灯 10 理解熟悉散转结构的程序 11 位操作指令的学习 12 比较指令的学习与cy位-All ports at the same time the high home ownership low, and constantly flashing 2 p1 I 3 way light water 2 hexadecimal understanding the relationship between the number of 3-port MCU adder: the 52h+ 0fch results sent p1 mouth 4 Singlechip multiplication: ff* 03h results to send binary adder p15 SCM SCM 6 2 7 learning Singlechip counter logic operations further study 8 MCU 9 cyclic shift logic operations instructions flowing light 10 scattered understanding of familiar procedures to the structure of 11 operating instruction instructions learn learning 12 compared with the cy-bit

用于蓝牙开发！基于hci的编程，可实现单片机对蓝牙模块的控制，从而实现蓝牙主从设备的连接和通信！-for Bluetooth development! Based on HCI programming can be realized right MCU Bluetooth module control, thereby achieving Bluetooth equipment from the main connection and communication!

使用MCU实现模糊算法-use MCU fuzzy algorithm

MSP430FE42X防窍电电表DEMO（编译器IAR3.42)-Anti-obsessed MSP430FE42X electric meter DEMO (compiler IAR3.42)

用ATmega8实现累加功能，并用数码管实现显示。-Cumulative function with ATmega8 realize, and realize digital tube display.

你是单片机初学者吗？那一定很想有一些源程序和电路图指导你吧！？那就看看这个单片机实验用程序及原理图集吧-you SCM beginners? I certainly would like to have some source circuit and guidance you! ? Then look at the MCU experimental procedures and principles Atlas it