-
本程序是通过TMS320CS2047的DSP处理器,经过DSP内部事件管理器的配合,实现SPWM波输出!...
本程序是通过TMS320CS2047的DSP处理器,经过DSP内部事件管理器的配合,实现SPWM波输出!-This procedure is adopted TMS320CS2047 of DSP processors, DSP, after the internal event manager with the realization of SPWM wave output!
- 2022-02-04 17:01:31下载
- 积分：1
-
msp430fe427登记定义头文件定义HEA MSP430FE427登记…
MSP430FE427头文件寄存器定义
MSP430FE427头文件寄存器定义
MSP430FE427头文件寄存器定义-MSP430FE427 register definition header files MSP430FE427 register definition header files MSP430FE427 register definition header files
- 2023-06-26 05:55:03下载
- 积分：1
-
这是三星arm s3c44b0x开发板上的一些实例程序，包括lcd，led，key，pwm，uart等...
这是三星arm s3c44b0x开发板上的一些实例程序，包括lcd，led，key，pwm，uart等-arm s3c44b0x development board some examples of procedures, including LCD, led, key, PWM, UART, etc.
- 2022-03-04 11:17:51下载
- 积分：1
-
Efficient C programming techniques for ARM Architecture.
Efficient C programming techniques for ARM Architecture.
- 2022-05-20 17:09:49下载
- 积分：1
-
Development Environment: ADS 1.2/SDT 2.51GUI test, because there is no touch scr...
开发环境:ADS 1.2/SDT 2.51
GUI测试，由于没有触摸屏，所以将触摸屏的代码给屏蔽了；
请将FS44B0II开发板连接好交叉网线、直连串口线、电源，
并连接好G57液晶屏，同时还要连接好背光电源；
然后在BIOS的命令窗口里面敲netrun命令；
点击FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel目录下：
批处理文件FS44B0_G57_uCGUI.BAT
下面你就可以看到液晶屏上面显示优龙标志
它会延时一两秒中进入下一个画面，逐步延时GUI的各项功能，请耐心观看；
-Development Environment: ADS 1.2/SDT 2.51GUI test, because there is no touch screen, it will be touch screen to shield the code Please FS44B0II development board to connect a good cross-network lines, direct serial lines, power supply, and connect a good G57 LCD screen, at the same time, good backlight power supply connection and then in the BIOS command window knock netrun order Click FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel directory: batch file FS44B0_G57_uCGUI.BAT below you can see the LCD screen above shows excellent signs that it will delay Liuzhou 1 two seconds to enter the next screen, and gradually delay the GUI features, please be patient watch
- 2022-02-06 06:38:46下载
- 积分：1
-
sdconfig.h: The document for the SD card reader module configuration header file...
sdconfig.h: 该文件为SD卡读写模块配置头文件，用户可根据实际硬件条件进行修改.
SD目录 : SD卡读写模块的全部文件,一般不用修改.
建议sdconfig.h文件不要放于SD目录中，因为SD目录中的文件一般无须修改,而sdconfig.h通常会有改动.
-sdconfig.h: The document for the SD card reader module configuration header files, the user hardware according to actual conditions can be modified. SD directory: SD card reader module all the documents, the general need not be amended. sdconfig.h document recommends not to put in SD directory, because the SD files in the directory are not normally required to be amended and the changes are usually sdconfig.h.
- 2022-03-12 03:53:48下载
- 积分：1
-
gps2参天大树
在WINCE6.0环境调试开发的ARM9-2440硬件串口通信程序，嵌入式ARM接受2串口，发送1串口数据，适时监控下位机发送的轮胎电压温度气压数据，经适时处理分析在7寸界面显示个车厢轮胎的状态信息，源码调试通过并在轻轨车上运行
- 2022-07-25 10:50:40下载
- 积分：1
-
为AU1200芯片linux系统所设计的LCD液晶显示驱动程序
为AU1200芯片linux系统所设计的LCD液晶显示驱动程序-AU1200 chip for linux system designed LCD Driver
- 2022-01-22 17:48:03下载
- 积分：1
-
三星arm 4510 bootloader的实现与分析
三星arm 4510 bootloader的实现与分析-Samsung realize the arm 4510 bootloader and Analysis
- 2023-08-29 22:50:03下载
- 积分：1
-
C8051F120 与双口RAM及CP200
C8051F120 与双口RAM及CP200的网络连接,能够将信号传给上位机软件.并且已经商用.
- 2022-01-26 14:47:56下载
- 积分：1
