-
8051IP nuclear source code (VHDL). RAR
8051IP 核源代码（VHDL）.RAR-8051IP nuclear source code (VHDL). RAR
- 2022-11-14 08:05:04下载
- 积分：1
-
1、ps/2键盘输入，通过led显示ascii码
2、稍等1s可以在lcd上显示输入的字符
3、其中键盘上的backspce键是用来清屏的
4、当l...
1、ps/2键盘输入，通过led显示ascii码
2、稍等1s可以在lcd上显示输入的字符
3、其中键盘上的backspce键是用来清屏的
4、当lcd上显示满字符时，在按下按键自动清屏，从第一行显示。-1, ps/2 keyboard input, through the led display ascii code 2, wait 1s in the lcd display characters input 3, which backspce keys on the keyboard was required to settle the screen 4, when the lcd display full of characters, the press the button automatically Qing-ping, from the first line of display.
- 2022-01-31 12:27:49下载
- 积分：1
-
MODELSIM的实验程序，在QUARTUSii中调用MODELSIM，实现仿真
MODELSIM的实验程序，在QUARTUSii中调用MODELSIM，实现仿真-ModelSim Experimental procedures QUARTUSii call MODELSIM, realize Simulation
- 2022-04-13 16:01:45下载
- 积分：1
-
SASX
Use of Kalman and EKF on two-phase permanent magnet synchronous motor of the state estimate CDCDCDCDCCC
- 2020-06-24 11:40:02下载
- 积分：1
-
traffic_lights
用Verilog实现的交通信号灯控制，主干道和支路通行的时间不相等(Using Verilog implementation of traffic signal control, the trunk road and the slip is not the same passage of time)
- 2009-03-28 18:31:31下载
- 积分：1
-
AGC
The AGC is a smart programmable gain amplifier (PGA). The amplifier gain is adjusted based upon
the input signal level so that the output is at a specified Target Gain. The AGC can be configured to
be either a mono or stereo input / output component. For illustration purposes, the following
discussion will highlight the stereo configuration.
- 2017-12-01 17:26:59下载
- 积分：1
-
i2c
说明： PIC32MX4系列单片机I2C总线模块示例代码
PIC32MX4系列单片机I2C总线模块示例代码PIC32MX4系列单片机I2C总线模块示例代码PIC32MX4系列单片机I2C总线模块示例代码(PIC32MX4 I2C
PIC32MX4 I2C
PIC32MX4 I2C
PIC32MX4 I2C)
- 2011-03-31 09:35:50下载
- 积分：1
-
DDR3读写测试
MIG IP控制DDR3读写测试，于MIG IP核用户接口时序较复杂，这里给出扩展接口模块用于进一步简化接口时序。(MIG IP controls DDR3 reading and writing tests, and the time sequence of MIG IP kernel user interface is more complex.)
- 2018-03-28 16:01:36下载
- 积分：1
-
Advanced-FPGA-Design
Advanced FPGA Design - Architecture, Implementation, and Optimization(Advanced FPGA Design- Architecture, Implementation, and Optimization)
- 2015-04-13 16:00:33下载
- 积分：1
-
daima
Rst是低电平有效的系统复位信号，Clk是时钟信号。AB[5：0]是地址信号，DB[7：0]是数据信号，wr是低电平有效的写信号。start是启动信号。
模块中有一个64x8的双端口的存储器。系统复位结束后，可以通过AB、DB和wr信号向同步存储器写入数据。当写入64个数据后，给出一个Clk周期宽度的脉冲信号start，则系统从存储器0地址处开始读出数据，读出的8位数据从低位开始以3位为一组，每个时钟周期输出一组，即第一个时钟周期输出[2：0]位，第二个时钟周期输出[5：3]位，第三个周期输出1地址的[0]位和0地址的[7：6]位，直至将存储器中64x8数据全部输出。若最后一组不足三位，则高位补0。
(Rst is an active-low system reset signal, Clk is a clock signal. AB [5: 0] is the address signal, DB [7: 0] is the data signal, wr write signal is active low. start is the start signal. Module in a dual port memory of 64x8. After the reset, you can write data to the synchronous memory by AB, DB and wr signals. When data is written to 64, given the width of a pulse signal Clk cycle start, the system begins to read the memory address 0, 8 data read out a low starting with three as a group, each clock outputs a set period, which is the first clock cycle of the output [2: 0] bits, the second clock cycle output [5: 3] position, the third cycle of the output of an address [0] and 0 address [7 : 6] bit, until all the data in memory 64x8 output. If the last group of less than three, the high 0s.)
- 2014-12-11 20:16:04下载
- 积分：1
