登录
首页 » 嵌入式系统 » 使用该控制器通用I / O端口I2C协议仿真源代码,第…

使用该控制器通用I / O端口I2C协议仿真源代码,第…

于 2022-09-08 发布 文件大小:1.52 kB
0 133
下载积分: 2 下载次数: 1

代码说明:

利用msp430的通用I/O端口模拟I2c协议的源代码,利用此代码可以不需要I2c模块即可进行I2C通信-use of the Controller General I/O Ports I2c agreement simulation source code, the use of this code can not I2c module can hold I2C communications

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 超小usb协议栈,完整实现!值得一看哦~
    超小usb协议栈,完整实现!值得一看哦~-Ultra-small usb protocol stack, complete realize! Well worth a visit ~
    2022-06-30 00:16:48下载
    积分:1
  • USB协议的细节,以及大量的网上信息。
    usb的协议细节,网上有很多信息。
    2022-05-15 09:48:44下载
    积分:1
  • 时钟的率调整程序
    时钟的率调整程序--Program to configure clock s frequency.
    2022-09-27 10:55:03下载
    积分:1
  • 51单片机程序
    集合了51单片机的经典源代码,均为原创,例如,键盘操作,数码管显示,秒表,中断操作,适合初学者学习,初学必备资料。另外还有一些51单片机的简单project,如简易计算器等
    2023-01-06 00:10:04下载
    积分:1
  • 单片机复位电路的可靠性设计复位电路的基本功能是 上电时提供复位信号直至电源稳定后撤销复位信号为可靠起 见电源稳定后还要经一定的延时才撤销复位信号以防...
    单片机复位电路的可靠性设计复位电路的基本功能是 系统上电时提供复位信号直至系统电源稳定后撤销复位信号为可靠起 见电源稳定后还要经一定的延时才撤销复位信号以防电源开关或电源插头分-合过程中引起的抖动而影 响复位-MCU reset circuit reliability design of the circuit" s basic function is to reset the system power-on reset signal until the system is to provide stable power to withdraw the sake of the reset signal as a reliable power supply stable even after a certain delay to revoke a reset signal to prevent the power switch or Power plug points- combined jitter caused in the course affected by reset
    2022-08-07 20:12:48下载
    积分:1
  • 建立在组态环境TRACEMODE基础下,实现数据采集、报表分析、控制算法...
    建立在组态环境TRACEMODE基础下,实现数据采集、报表分析、控制算法- The establishment under the configuration environment TRACEMODE foundation, realizes the data acquisition, the statement analysis, the control algorithm
    2022-05-30 00:06:37下载
    积分:1
  • Pic 16f874 Modbus
    我需要的代码,以沟通 PIC 16f874 单片机与 ML1400 PLC,通过 modbus RTU 奴隶协议连接到单片机的 lcd 中写入数据......请给我发送代码,如果有任何这一项目。 
    2023-01-18 05:00:04下载
    积分:1
  • AT91RM9200的USB host和USB device的代码ADS1.2. USB
    AT91RM9200的USB host和USB device的代码ADS1.2. USB-Device测试程序: 因为程序运行在SDRAM中,所以要先初始化SDRAM(可用basic boot程序初始,之后不能复位或断电),再运行此程序,程序运行后连接USB端口,计算机会提示检测到新硬件,安装硬件驱动程序atmusb6119.inf 后计算机会把USB端口虚拟为一个串行的端口使用-AT91RM9200 the USB host and USB device code ADS1.2.USB-Device test procedure: Because the procedure is running in SDRAM, and so we have to initialize SDRAM (available for the initial basic boot procedure, followed by Can not reset or power off), then Run this program, the program to run after connecting USB port, the computer will be prompted to detect the new hardware, installing hardware drivers after the computer will atmusb6119.inf virtual USB port to a serial port to use
    2022-01-30 16:36:24下载
    积分:1
  • iic代码的源文件
    iic 驱动代码,
    2022-07-25 17:43:43下载
    积分:1
  • S3C44B0X开发板设计的原理图资料,可以对自己开发基于S3C44B0X的电路板起到很好的借鉴!...
    S3C44B0X开发板设计的原理图资料,可以对自己开发基于S3C44B0X的电路板起到很好的借鉴!-S3C44B0X development board schematic design data, based on its own development S3C44B0X circuit boards serve as a good reference!
    2022-04-11 19:20:30下载
    积分:1
  • 696518资源总数
  • 105877会员总数
  • 14今日下载