登录
首页 » 嵌入式系统 » TI射频卡驱动,可以直接使用 TI射频卡驱动,可以直接使用

TI射频卡驱动,可以直接使用 TI射频卡驱动,可以直接使用

于 2022-12-01 发布 文件大小:3.40 MB
0 127
下载积分: 2 下载次数: 1

代码说明:

TI射频卡驱动,可以直接使用 TI射频卡驱动,可以直接使用-TI RF card driver can directly use TI RF card driver can directly use

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • GSM基于GPS的车载监控
    该系统不断地观察一个移动的车辆和报告需求的状态。当防盗识别时,负责 人发短信给单片机,单片机再发出控制信号,停止引擎马达。授权人需要送 密码给控制器以重新启动车辆,打开门。这是更安全的,可靠的,成本低。  为此,我们采用AT89S52单片机接口与GSM和GPS。请通过我们清楚地提到的所有端口输入输出注意事项的代码。 同时,我们用来检查密码来解锁车子....
    2022-12-26 03:45:03下载
    积分:1
  • 这是usb驱动的源码,仅供参考,可花费了好长时间才调通的...
    这是嵌入式usb驱动的源码,仅供参考,可花费了好长时间才调通的-This is embedded usb driver source for reference purposes only and may spend a good long time to tune
    2022-08-18 18:39:46下载
    积分:1
  • 通过按键在3位一体的数码管上显示数字,能显示00~99,但是减法只能从9减到0,在KEILC上编译调试成功...
    通过按键在3位一体的数码管上显示数字,能显示00~99,但是减法只能从9减到0,在KEILC上编译调试成功-Through the button in one of three digital tube display figures, can show 00 ~ 99, but the subtraction can only be reduced to 0 from 9 in the debugging KEILC compiled successfully
    2022-01-25 23:33:08下载
    积分:1
  • FPGA的数码相框
    FPGA的数码相框,实现SD卡内图片的读取显示,代码风格不错,有详细注释,对初学者很有用, 希望对各位有所帮助,谢谢!
    2022-01-25 15:59:09下载
    积分:1
  • 基于AT91SAM7SE512cpu使用SDRAM的例子,编译工具是IAR4_31A
    基于AT91SAM7SE512cpu使用SDRAM的例子,编译工具是IAR4_31A-AT91SAM7SE512cpu based on examples of the use of SDRAM, the compiler tool is IAR4_31A
    2022-03-14 23:21:04下载
    积分:1
  • 基于EDA的“梁祝”音乐播放设计,运用data_rom的查找表功能
    基于EDA的“梁祝”音乐播放设计,运用data_rom的查找表功能-Based on EDA" s " Butterfly Lovers" Music Player Design
    2022-10-25 19:20:03下载
    积分:1
  • 12位ADC
    汇编语言编写的代码AT89C2051的MCP320212位ADC读取程序
    2022-09-23 02:55:03下载
    积分:1
  • CM240128程序,可用keil编译,用51单片机可运行此程序
    CM240128程序,可用keil编译,用51单片机可运行此程序-CM240128 procedures available keil compiler, using 51 single-chip can run this program
    2023-07-09 03:15:03下载
    积分:1
  • linux
    嵌入式linux- Inserts type linux
    2022-02-28 13:49:47下载
    积分:1
  • DE2 练习源码2-1
    Part I We wish to display on the 7-segment displays HEX3 to HEX0 the values set by the switches SW15−0. Let the values denoted by SW15−12, SW11−8, SW7−4 and SW3−0 be displayed on HEX3, HEX2, HEX1 and HEX0, respectively. Your circuit should be able to display the digits from 0 to 9, and should treat the valuations 1010 to 1111 as don’t-cares. 1. Create a new project which will be used to implement the desired circuit on the Altera DE2 board. The intent of this exercise is to manually derive the logic functions needed for the 7-segment displays. You should use only simple VHDL assignment statements in your code and specify e
    2022-03-23 22:31:42下载
    积分:1
  • 696518资源总数
  • 105873会员总数
  • 12今日下载