-
51 Series MCU
基于51系列单片机的4×4矩阵式键盘识别.正在学习单片机-51 Series MCU-based 4 × 4 matrix keyboard identification. Are learning Singlechip
- 2022-06-02 11:26:13下载
- 积分：1
-
该源代码为单片机的火车时刻表课程设计源代码，需要课程设计报告的，再找我。...
该源代码为单片机的火车时刻表课程设计源代码，需要课程设计报告的，再找我。-The source code for the MCU train schedules curriculum design source code, the need for curriculum design report, I find.
- 2022-02-03 11:47:51下载
- 积分：1
-
让数码管的亮度一致,原代码是运行在AT89S52上,12MHz
让数码管的亮度一致,原代码是运行在AT89S52上,12MHz-The brightness of the digital control line, the original code is run on AT89S52 on, 12MHz
- 2022-02-09 21:35:35下载
- 积分：1
-
关于51单片机控制595驱动的数码管程序，编译过，可直接使用，有HEX文件...
关于51单片机控制595驱动的数码管程序，编译过，可直接使用，有HEX文件-51 single-chip 595 on control-driven digital control procedures, the compiler, and can be used directly, there are HEX file
- 2022-03-11 16:39:46下载
- 积分：1
-
单片机 步进电机控制原代码
单片机 步进电机控制原代码-stepper motor control microcontroller source code
- 2023-08-26 03:50:03下载
- 积分：1
-
TFT+LCD驱动原理详细的pdf资料，开发者必备
TFT+LCD驱动原理详细的pdf资料，开发者必备-TFT+ LCD driving principle detailed pdf data, developers must
- 2022-03-05 15:56:38下载
- 积分：1
-
单片机P1口与4个按键连接，用于信号幅度和频率调节操作键。单片机P0、P2.7、P3.6(
单片机P1口与4个按键连接，用于信号幅度和频率调节操作键。单片机P0、P2.7、P3.6(-WR)与DA0832、2个741(运放)连接构成波形信号输出电路。
编程使波形信号输出电路输出正弦波信号，并且可通过操作键调节信号的幅度和频率。幅度和频率调节级别从0~10，共11个等级。
-Singlechip P1 I connect with the four buttons for the signal amplitude and frequency adjustment operation keys. Singlechip P0, P2.7, P3.6 (-WR) and DA0832, 2 months 741 (operational amplifier) to connect constitute waveform signal output circuit. Programming so that waveform signal output circuit output sine wave signal, and can be operated keys adjust the signal amplitude and frequency. Amplitude and frequency adjustment level from 0 ~ 10, a total of 11 grades.
- 2022-04-14 22:06:25下载
- 积分：1
-
This is an MCU with a simple calculator
这是一用单片机实现的简单计算器-This is an MCU with a simple calculator
- 2022-07-23 20:23:19下载
- 积分：1
-
With the program AD9854C.exe one can set and tune the frequency in CW
With the program AD9854C.exe one can set and tune the frequency in CW-mode. For use as a receiver LO also IF can be given and the both possible receiving frequencies are printed on the screen. The level in Q-outputs can be varied by giving the wanted attenuation in dB. This function is done by controlling a 12b digital multiplier in the device. In this case the level decreases somewhat with increasing frequency as it does in DDS devices. Alternatively the inverse sinc correction can be chosen, in which case the output is flat and high. -With the program AD9854C.exe one can set and tune the frequency in CW-mode. For use as a receiver LO also IF can be given and the both possible receiving frequencies are printed on the screen. The level in Q-outputs can be varied by giving the wanted attenuation in dB. This function is done by controlling a 12b digital multiplier in the device. In this case the level decreases somewhat with increasing frequency as it does in DDS devices. Alternatively t
- 2022-08-02 19:18:16下载
- 积分：1
-
很好的pid温控
代码，分享一下，
很好的pid温控
代码，分享一下，-Pid temperature control very good code, share,
- 2022-03-18 06:26:12下载
- 积分：1
