-
ucgui that porting to 2410 processor
ucgui that porting to 2410 processor
- 2023-04-12 04:25:03下载
- 积分：1
-
一种用于液晶显示器的接口代码
its an interfacing code for LCD in arm platform
- 2022-03-19 21:35:18下载
- 积分：1
-
s3c2410技术手册中文版第6章，学习嵌入式的必要章节。
s3c2410技术手册中文版第6章，学习嵌入式的必要章节。-S3C2410 technical manual Chinese edition Chapter 6, learning the necessary embedded sections.
- 2022-07-18 05:26:07下载
- 积分：1
-
一个用LP2148实现的MP3工程，包括FAT文件系统，采用SD卡
一个用LP2148实现的MP3工程，包括FAT文件系统，采用SD卡-LP2148 realize a use of the MP3 works, including the FAT file system, the use of SD cards
- 2023-08-04 04:15:03下载
- 积分：1
-
arm基础学习的东东，很实用，初学者请留意哇
arm基础学习的东东，很实用，初学者请留意哇-for junior of arm studing
- 2023-05-11 22:20:02下载
- 积分：1
-
代码用简单的4个IO口外加两个ADC转换接口实现了触摸屏全套控制流程....
代码用简单的4个IO口外加两个ADC转换接口实现了触摸屏全套控制流程.-Code with a simple four IO port plus two ADC conversion of the touch screen interface to achieve a full set of control flow.
- 2022-01-25 15:50:33下载
- 积分：1
-
四路循迹
四路寻迹传感器有信号(白线）为0 没有信号（黑线）为1四路寻迹传感器电源+5V GND 取自于单片机板靠近液晶调节对比度的电源输出接口关于单片机电源：本店驱动模块内带LDO稳压芯片，当电池输入最低的电压6V时候可以输出稳定的5V分别在针脚标+5 与GND 。这个电源可以作为单片机系统的供电电源。
- 2022-05-19 18:59:21下载
- 积分：1
-
这是关于fpga为控制芯片的硬件设计资料，可以了解到fpga设计的特点...
这是关于fpga为控制芯片的硬件设计资料，可以了解到fpga设计的特点-they simply this is for the control of the hardware chip design information, we can see that they simply design features
- 2022-11-14 15:30:04下载
- 积分：1
-
周立功公司为LPC213X编写的 ARM7 嵌入式文件系统，运行于UC/COS系统。...
周立功公司为LPC213X编写的 ARM7 嵌入式文件系统，运行于UC/COS系统。-weeks meritorious LPC213X prepared for the ARM7 Embedded file system, running on UC/COS system.
- 2022-02-18 15:32:45下载
- 积分：1
-
This example program shows how to configure and use the
A/D Converter of the fo...
This example program shows how to configure and use the
A/D Converter of the following microcontrollers:
* Philips LPC 2114/2119/2124/2129/2131/2132/2138/2194
After configuring the A/D Converter, the program reads
A/D channel 0 and outputs the converted value using the serial
port.
To run this program...
1. Select the Device (Project - Options for Target - Device)
2. Build the project (Project - Build Target)
3. Start the uVision Debugger
4. Open the Serial Window (View - Serial Window 1)
5. Click Run (F5)
6. Click on the Toolbox buttons to change input voltages
A debug script (debug.ini) creates buttons that set different
analog values in A/D channels. As the program runs, you
will see the A/D input and output change.
Other buttons create signals that generate sine wave
or sawtooth patterns as analog inputs. µ Vision3 users may
enable the built-in Logic Analyzer to view, measure and compare
these input signals grap
- 2022-01-31 01:19:45下载
- 积分：1
