登录
首页 » Asm » jtcutsj

jtcutsj

于 2009-12-11 发布 文件大小:30KB
0 160
下载积分: 1 下载次数: 4

代码说明:

  静态存储体设计 包含设计步骤, 原理图 设计心得等(Static memory bank design consists of design steps, such as schematic design experience)

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • MY-FOOTPRINT
    Altium designer10的常用元器件封装库(footprint for ad10)
    2015-04-21 20:59:39下载
    积分:1
  • 6通用定时器PWM—呼吸灯
    说明:  基于Stm32F103C8T6的PWM呼吸灯,由PWM占空比调节LED灯的亮度(PWM breathing lamp based on stm32f103c8t6)
    2020-07-03 15:42:59下载
    积分:1
  • 基于51的非接触式红外测温
    说明:  通过使用mlx90614获取外界温度数据经51单片机量化编码在OLED 屏幕上显示出数值以实现红外温度测量(By using MLX90614 to obtain the external temperature data, the infrared temperature measurement can be realized by displaying the numerical value on OLED screen with 51 single chip microcomputer quantization coding)
    2021-03-21 13:29:17下载
    积分:1
  • lab
    基于MSP430F5529和DS18B20温度传感器的检测温度的程序(Based on the detected temperature of the temperature sensor DS18B20 MSP430F5529 and procedures)
    2020-12-17 22:29:12下载
    积分:1
  • 16BITE_PWM
    基于mega16的十六位PWM波的配置和说明。(mega16 PWM)
    2012-04-24 18:28:28下载
    积分:1
  • 实验1 跑马灯实验
    这是基于STM32F103ZET6的原子开发板精英版的跑马灯程序(This is an elite version of the Atomic Development Board based on STM32F103ZET6.)
    2019-06-11 14:54:23下载
    积分:1
  • STM32_AD9954-master
    说明:  STM32控制AD9954产生正弦波等波形,频率幅值可调,各种调制。(STM32 controls AD9954 to generate sinusoidal wave, frequency amplitude adjustable, various modulation.)
    2020-06-20 19:00:02下载
    积分:1
  • redout
    红外报警器的c代码。 基于清翔电子的c51单片机最小开发板开发,代码带有注释。如果不布置外围红外电路,IO口检测到低电平触发蜂鸣器报警。必须有液晶1602才能正常运行程序,不然需要注释掉LCD相关代码。(Infrared alarm c code. Based on Qingxiang electronic C51 microcontroller development board, the code with notes. If the peripheral infrared circuit is not arranged, the low level trigger buzzer alarm is detected at the IO port. There must be liquid crystal 1602 to run the program normally, otherwise you need to annotate the LCD related code.)
    2018-10-22 23:43:47下载
    积分:1
  • windfarm_dfig
    PSCAD/EMTDC软件搭建的双馈异步发电机(DFIG)详细模型,转子侧采用定子磁链定向控制,网侧采用电网电压定向控制。(PSCAD/EMTDC software to build double-fed induction generator (DFIG) detailed model, using the rotor side stator flux oriented control, network side using the grid voltage oriented control.)
    2016-08-06 00:26:18下载
    积分:1
  • POWER
    用单片机控制输出电压,MCU控制输出,我没有用过,大家可以参考(MCU control the output voltage, MCU control output, I have not used, we can refer to)
    2014-01-09 16:26:36下载
    积分:1
  • 696516资源总数
  • 106571会员总数
  • 2今日下载