-
edge-and-GUI
图像边缘检测，并有gui界面的设计 有matlab程序生成exe的部分内容(detection of the image edge and establish
the gui)
- 2013-09-19 10:34:11下载
- 积分：1
-
breastedge
乳腺图像轮廓提取，配准和分割的预处理工作(breast registration)
- 2011-10-23 08:19:54下载
- 积分：1
-
luboqi
设计一个8阶以内的带通滤波器，通带截止频率fc1=30070HZ，fc2=32170HZ，通带内允许最大衰减0.2dB。设计满足要求的Butterworth滤波器和chebyshev滤波器。以RC运放为基本单元以最易实现的原则完成电路设计及参数选择，并根据设计参数进行幅频特性和相频特性的仿真，给出仿真曲线。分析电路的无源灵敏度。(Design within an 8-order band-pass filter, the passband cutoff frequencies FC1 = 30070HZ, FC2 = 32170HZ allow maximum attenuation 0.2dB within the passband. Designed to meet the requirements of the Butterworth filter and chebyshev filter. RC op amp is the basic unit is the most easy to implement the principle of complete circuit design and parameter selection, and in accordance with the design parameters of the amplitude-frequency characteristics and phase-frequency characteristics of the simulation, simulation curve. Passive sensitivity of the analysis circuit.)
- 2013-03-27 21:10:38下载
- 积分：1
-
MTD--Hamming
动目标检测（MTD）领域的仿真，画出了加汉明窗之后的频率响应曲线，经调试，可以运行(Moving target detection (MTD) in the field of simulation, draw the frequency response curve after Hamming window, debugging, you can run)
- 2021-04-19 16:18:51下载
- 积分：1
-
Newton
此源码用于对一些非线性的方程组进行求解，时间复杂度比较小，效率比较高(This source is used for some non-linear equations is solved, the time complexity is relatively small, more efficient )
- 2011-09-11 03:09:57下载
- 积分：1
-
delta_figure
MATLAB CODE FOR DELTA MODULATION TECHNIQUE FOR ANY SIGNALS
- 2013-11-20 13:33:51下载
- 积分：1
-
Kfisher
introduction of kfisher
- 2007-11-24 21:20:39下载
- 积分：1
-
fsk
用数值方法实现该fsk信号的相关型解调器，完成一个二进制fsk通信系统的仿真(Numerical methods used in the implementation of the relevant type fsk signal demodulator, to complete a binary fsk communication system simulation)
- 2009-03-19 15:38:30下载
- 积分：1
-
SS
说明： 本算法描述了如何利用小波变换进行水印的嵌入与提取(The algorithm described how to use wavelet transform embedding and extracting)
- 2009-11-18 10:50:30下载
- 积分：1
-
HoneycombPattern_new
L为正六边形边长，默认10
H为1*2的向量，H(1)和H(2)分别代表待填充矩形的x和y方向的边长,默认[100 100]
若H输入为1*1尺寸，则默认为边长为H的正方形
返回值为所有六边形的顶点横纵坐标
调用举例：
HoneycombPattern_new
HoneycombPattern_new(5)
HoneycombPattern_new(1,[50 40])
作者：Neptune_zx(@MATLAB Forum)
Time：2010/11/06">
- 2011-04-20 08:31:14下载
- 积分：1
