-
1602C
文件名：lcd1602lib.h
内 容：1602液晶的控制端口、数据端口和相关操作(The file name: lcd1602lib. H
* inside let: 1602 LCD control port, data port and related operations
)
- 2012-05-08 15:15:36下载
- 积分：1
-
callback
说明： This is code of UVM CALLBACK function.
- 2020-06-24 15:40:02下载
- 积分：1
-
LDPC码的编码和解码过程。有testbentch。
ldpc编解码程序。有testbentch。-ldpc encoding and decoding process. There testbentch.
- 2022-03-12 16:50:03下载
- 积分：1
-
新建
MCP4725实现的i2c驱动程序，通过DA转换实现函数发生器(MCP4725 come ture i2c drive program,Through da conversion function generator in English)
- 2017-06-18 10:42:07下载
- 积分：1
-
用例化语句和case语句编写的全加器的VHDL描述。
用例化语句和case语句编写的全加器的VHDL描述。-Of statements were prepared using the full adder of the VHDL description.
- 2022-01-26 02:45:15下载
- 积分：1
-
This is is a bridge IP core to interface the Tensilica PIF bus protocol with the...
This is a bridge IP core to interface the Tensilica PIF bus protocol with the OpenCores WishBone. It currently supports single-cycle as well as burst transfer operations. The core has been tested in a master-PIF slave-WB configuration.-This is is a bridge IP core to interface the Tensilica PIF bus protocol with the OpenCores WishBone. It currently supports single-cycle as well as burst transfer operations. The core has been tested in a master-PIF slave-WB configuration.
- 2022-04-07 07:47:24下载
- 积分：1
-
EDA常用双LED显示译码程序，将四位二进制数译码为七位对应于LED7位输入的高低电平信号...
EDA常用双LED显示译码程序，将四位二进制数译码为七位对应于LED7位输入的高低电平信号-EDA common dual LED display decoding procedure will be four binary decoding for seven LED7 spaces corresponding to the input signal circuits
- 2022-06-29 02:03:32下载
- 积分：1
-
400rdm
用于FPGA的学习，大家值得借鉴，可以好好学习一下(this is for fpga and you can use this.)
- 2020-06-16 15:20:02下载
- 积分：1
-
buffer_display是4X4KEYPAD的输出显示模块。可以显示6个连续的按键...
buffer_display是4X4KEYPAD的输出显示模块。可以显示6个连续的按键-buffer_display is 4X4KEYPAD output module. It showed six consecutive Press
- 2022-12-12 05:35:03下载
- 积分：1
-
chuankou
说明： 本实验为UART回环实例，实验程序分为顶层unrt_top、发送模块uart_tx、接收模块 uart_rx，以及时钟产生模块clk＿div。uart＿rx将收到的包解析出8位的数据，再传送给 uart_tx发出，形成回环。参考时钟频率为100MHz，波特率设定为9600bps。(This experiment is an example of UART loop. The experimental program is divided into top-level unrt_top, sending module uart_tx, receiving module uart_rx, and clock generation module clk_div. Uart_rx parses the received packet into 8 bits of data and sends it to uart_tx to send out, forming a loop. The reference clock frequency is 100 MHz and the baud rate is set to 9600 bps. stay)
- 2020-06-24 01:40:02下载
- 积分：1
